| Toolnumber |
Tool Description |
|
CMM Alt Toolnumber |
CATANA Toolnumber |
| 20HME65B94200-1 | Sling Equipment, Inlet Cowl, CF6-50 & RB211-524 | | Replaced by G71032-1 | |
| 289544-6 | Tester, APU Fuel Manifold | | Replaced by 833563-6 | |
| 294864-1 | Wrench, APU Transducer Removal | | | |
| 2CF65B05528-1 | Balance Stand, Outbd Aileron & Elevator & Upp Rddr | | | |
| 2ME65B00002 | Wrench - Spanner, Safety Lanyard, Tiedown Locks | | | |
| 2ME65B89603 | Accessory Adapter - Hoist System RB211 & CF6-50 | | Replaced by G24013-1 | |
| 2MIT114T4000 | Spacer Kit - Inbd/Outb Slat Installation | | | |
| 30HME65B89603 | Sling Equipment, Nose Cowl, RB211-524 & CF6-50 | | Replaced by G71030-1 | |
| 3MIT65B89603 | Tool Set, RB211 Engine Mount Bolt | | | |
| 3OHME65B00002 | Sling - Tethering/Lifting Airplane Recovery | | Replaced by J07008-1 | |
| 42A12 | Pinglite | | Replaced by PL1 | |
| 4MIT65B80307-1 | Protractor Assembly - Control Column | | Alternative of A27021-29 | |
| 5ME65-73788 | Static Balance Equipment, Control Surfaces | | Replaced by F70330-4 | |
| 5ME65-73788 | Static Balance Equipment, Control Surfaces | | Replaced by F70330-87 | |
| 732021 | Cover, RAT Turbine Blade | | | |
| 734734 | Protective Cover, RAT Hub | | | |
| 810-325 | Spanner Wrench | | | |
| 833563-6 | Tester, APU Fuel Manifold | | | |
| 900-24999 | Inspection Plate - QAD | | | |
| 906-10246-3 | Loop Resistance Test Set | | | |
| 906-10272-5 | Calibration Unit, Loop Resistance Tester | | | |
| A07001-1 | Jack Adapter - Forward Body | | Replaced by A07001-11 | |
| A07001-11 | Jack Adapter - Forward Body | | | |
| A07002-1 | Emergency Jacking Equipment - NLG | | | |
| A07003-1 | Jack Adapter - Outboard wing | | | |
| A07004-1 | Jacking Bar Set - MLG Axle | | Replaced by A07008-1 | |
| A07004-8 | Jacking Bar Set - MLG Axle | | Replaced by A07008-1 | |
| A07005-1 | Hoist Adapter - Airplane Recovery | | | |
| A07005-2 | Hoist Adapter - Airplane Recovery | | | |
| A07006-1 | Torque Multiplier Eqmnt, Tension Bolts, Vertcl Fin | | | |
| A07007-25 | Sling, vertical Fin Installation & Removal | | Replaced by A07007-33 | |
| A07007-33 | Sling, vertical Fin Installation & Removal | | | |
| A07008-1 | Jacking Bar Equipment - MLG Axle | | Replaced by A07008-19 | |
| A07008-19 | Jacking Bar Equipment - MLG Axle | | Alternative of A07008-25 | |
| A07008-19 | Jacking Bar Equipment - MLG Axle | | Alternative of A07008-26 | |
| A07008-19 | Jacking Bar Equipment - MLG Axle | | Alternative of A07008-27 | |
| A07008-19 | Jacking Bar Equipment - MLG Axle | | Alternative of A07008-28 | |
| A07008-19 | Jacking Bar Equipment - MLG Axle | | Alternative of A07008-29 | |
| A07008-25 | Jacking Bar Equipment - MLG Axle | | | |
| A07008-26 | Jacking Bar Equipment - MLG Axle | | | |
| A07008-27 | Jacking Bar Equipment - MLG Axle | | | |
| A07008-28 | Jacking Bar Equipment - MLG Axle | | | |
| A07008-29 | Jacking Bar Equipment - MLG Axle | | | |
| A07009-1 | Jacking Bar Equipment - MLG Axle | | | |
| A07011-1 | Hoist equipment, Airplane Recovery, w/o MLG | | | |
| A07011-2 | Hoist equipment, Airplane Recovery, w/o MLG | | | |
| A09003-1 | Lock Pin, None Gear Towing Lever | | Replaced by A09003-2 | |
| A09003-2 | Lock Pin, None Gear Towing Lever | | | |
| A10002-1 | Rem/Inst Pole, Pitot-Static Probe Cover | | Replaced by A10002-9 | |
| A10002-9 | Rem/Inst Pole, Pitot-Static Probe Cover | | | |
| A12001-1 | Fuel Sampling Equipment | | Replaced by A12001-14 | |
| A12001-14 | Fuel Sampling Equipment | | | |
| A12004-1 | Platform - Access, MLG Wheel Well | | Replaced by A12004-40 | |
| A12004-40 | Platform - Access, MLG Wheel Well | | | |
| A12005-1 | Lubrication Adapter - Attach Fitting, Wing/Nacelle | | | |
| A12006-1 | Ladder - Access Door, E/E Bay | | | |
| A12007-11 | Adapter - Tire Inflation | | Replaced by A12007-23 | |
| A12007-20 | Adapter - Tire Inflation | | | |
| A12007-23 | Adapter - Tire Inflation | | | |
| A12008-1 | Lubrication Adapter - Aft Wheel Well Blkhd, Bearng | | | |
| A20001-55 | Boom Hoist - General | | Replaced by A20001-83 | |
| A20001-65 | Boom Hoist - General | | | |
| A20001-79 | Boom Hoist - General | | Replaced by A20001-82 | |
| A20001-82 | Boom Hoist - General | | | |
| A20001-83 | Boom Hoist - General | | | |
| A20002-1 | Attach Fitting Set -Wing & Hor Stab, Safty Harness | | Replaced by A20002-4 | |
| A20002-4 | Attach Fitting Set -Wing & Hor Stab, Safty Harness | | | |
| A20004-1 | Set - Rig Pin | | Replaced by A20004-72 | |
| A20004-2 | Set - Rig Pin | | | |
| A20004-3 | Set - Rig Pin | | Replaced by A20004-68 | |
| A20004-64 | Set - Rig Pin | | Replaced by A20004-72 | |
| A20004-68 | Set - Rig Pin | | | |
| A20004-70 | Set - Rig Pin | | | |
| A20004-72 | Set - Rig Pin | | Replaced by A20004-78 | |
| A20004-76 | Set - Rig Pin | | | |
| A20004-78 | Set - Rig Pin | | | |
| A20005-1 | Clamp - Control Cable | | Replaced by A20005-9 | |
| A20005-5 | Clamp - Control Cable | | Replaced by A20005-9 | |
| A20005-9 | Clamp - Control Cable | | | |
| A20006-1 | Installation Set - NAS1368 Grommet | | Replaced by A20006-32 | |
| A20006-32 | Installation Set - NAS1368 Grommet | | | |
| A20007-1 | Test Tool - Stripping Force,Wrappd Wire Connection | | | |
| A20008-1 | Socket Set - Spherical Bearing | | | |
| A20011-1 | Bushing Rem/Inst Kit - Landing Gear Lock Link | | Replaced by A20011-22 | |
| A20011-22 | Bushing Rem/Inst Kit - Landing Gear Lock Link | | Replaced by A20011-64 | |
| A20011-64 | Bushing Rem/Inst Kit - Landing Gear Lock Link | | Replaced by A20011-76 | |
| A20011-76 | Bushing Rem/Inst Kit - Landing Gear Lock Link | | | |
| A20012-10 | Swaging Tool - Bearing | | | |
| A20012-11 | Swaging Tool - Bearing | | | |
| A20013-1 | Work Table - Pilot Aisle Stand | | | |
| A21001-1 | Hoist Adapters - Air Conditioning Pack | | Replaced by A21001-44 | |
| A21001-34 | Hoist Adapters - Air Conditioning Pack | | Replaced by A21001-45 | |
| A21001-44 | Hoist Adapters - Air Conditioning Pack | | | |
| A21001-45 | Hoist Adapters - Air Conditioning Pack | | | |
| A21002-1 | Rem/Inst Eqpmnt - Avionics Cooling Refrigertn Unit | | | |
| A21004-1 | Test Box - Current Sensor Fan ECS | | | |
| A21007-1 | Hold-Open Rod - Ram Air Door, Fligth Dispatch | | | |
| A21008-1 | Hold Open Set - Cabin Air Outflow | | | |
| A21009-1 | Blanking Plate - Equipment Cooling Monitor | | | |
| A21010-57 | Vacuum Tank - Pressure Relief Valve Test | | Replaced by A21010-70 | |
| A21010-63 | Vaccum Tank - Pressure Relief Valve Test | | Replaced by A21010-69 | |
| A21010-69 | Vacuum Tank - Pressure Relief Valve Test | | Replaced by A21010-70 | |
| A21010-70 | Vacuum Tank - Pressure Relief Valve Test | | Replaced by A21010-72 | |
| A21010-72 | Vacuum Tank - Pressure Relief Valve Test | | | |
| A21011-1 | Test Equipment - Low Limit Valve | | Replaced by A21011-6 | |
| A21011-6 | Test Equipment - Low Limit Valve | | | |
| A21012-1 | Test Gauge - Instrument Cooling Monitor System | | | |
| A21013-1 | Hoist Adapter Equipment - Air Conditioning Pack | | Replaced by A21013-50 | |
| A21013-50 | Hoist Adapter Equipment - Air Conditioning Pack | | | |
| A21014-1 | Lock - Hold Open, Outflow Valve | | | |
| A22001-15 | RCU - Maintenance Control Display Panel | | Replaced by A22001-22 | |
| A22001-22 | RCU - Maintenance Control Display Panel | | | |
| A22003-1 | Component Maintence Equipmnt - Autothrottle Clutch | | Replaced by A22003-20 | |
| A22003-20 | Component Maintence Equipmnt - Autothrottle Clutch | | Replaced by A22003-22 | |
| A22003-22 | Component Maintence Equipmnt - Autothrottle Clutch | | | |
| A22004-1 | Checking Fixture - Autothrottle Gearbox | | | |
| A22005-1 | Breakout Box - ATS Loadboard Yaw Damper Mntr Rcvr | | | |
| A22005-9 | Breakout Box - ATS Loadboard Yaw Damper Mntr Rcvr | | | |
| A22006-1 | Breakout Box - Fault Display PCA, Yaw Damper | | | |
| A22007-1 | Breakout Box - Arinc/Filter/Fuse PCA, Yaw Damper | | | |
| A22008-1 | Rigging Equipment - Autothrottle Brake | | Replaced by A22008-17 | |
| A22008-17 | Rigging Equipment - Autothrottle Brake | | Replaced by A22008-26 | |
| A22008-26 | Rigging Equipment - Autothrottle Brake | | | |
| A23001-1 | Acoustic Coupler - Attendant's Handset | | | |
| A23001-4 | Acoustic Coupler - Attendant's Handset | | | |
| A23001-8 | Acoustic Coupler - Attendant's Handset | | | |
| A23001-9 | Acoustic Coupler - Attendant's Handset | | | |
| A23002-1 | Test Box Assembly - TV Antenna Coupler | | Replaced by A23002-14 | |
| A23002-14 | Test Box Assembly - TV Antenna Coupler | | | |
| A23003-29 | Test Box - PC Cards, Audio Accessory Unit | | Replaced by A23003-41 | |
| A23003-30 | Test Box - PC Cards, Audio Accessory Unit | | Replaced by A23003-41 | |
| A23003-34 | Test Box - PC Cards, Audio Accesory Unit | | Replaced by A23003-41 | |
| A23003-41 | Test Box - PC Cards, Audio Accessory Unit | | | |
| A23003-42 | Test Box - PC Cards, Audio Accessory Unit | | | |
| A23004-1 | Test Box - Flight Attendant Interphone | | | |
| A23006-1 | Test Box - Audio Accessory Unit | | Replaced by A23006-26 | |
| A23006-16 | Test Box - Audio Accessory Unit | | Replaced by A23006-26 | |
| A23006-22 | Test Box - Audio Accessory Unit | | Replaced by A23006-26 | |
| A23006-23 | Test Box - Audio Accessory Unit | | Replaced by A23006-26 | |
| A23006-26 | Test Box - Audio Accessory Unit | | Replaced by A23006-45 | |
| A23006-27 | Test Box - Audio Accessory Unit | | Replaced by A23006-46 | |
| A23006-34 | Test Box - Audio Accessory Unit | | Replaced by A23006-39 | |
| A23006-39 | Test Box - Audio Accessory Unit | | Replaced by A23006-47 | |
| A23006-45 | Test Box - Audio Accessory Unit | | Replaced by A23006-47 | |
| A23006-46 | Test Box - Audio Accessory Unit | | Replaced by A23006-47 | |
| A23006-47 | Test Box - Audio Accessory Unit | | | |
| A23009-20 | Test Box - Audio Selector Panel | | Replaced by A23009-31 | |
| A23009-25 | Test Box - Audio Selector Panel | | Replaced by A23009-31 | |
| A23009-31 | Test Box - Audio Selector Panel | | | |
| A23011-1 | Test Box - Power Supply, Audio Accessory Unit | | | |
| A24001-1 | Hoist Equipment - LRU's Main EE Bay | | | |
| A24001-5 | Hoist Equipment - LRU's Main EE Bay | | | |
| A24004-1 | Test Relay - Isolation Request, Power Distribution | | | |
| A24005-1 | Load Bank - DC Generation System | | | |
| A24006-1 | Hoist Equipment - APU Battery | | | |
| A24007-1 | Support - Electrical Ground Power Cable | | | |
| A24008-1 | Test Box - Hydr Motor Driven Gen. Control Unit | | Replaced by A24008-19 | |
| A24008-19 | Test Box - Hydr Motor Driven Gen. Control Unit | | Replaced by A24008-37 | |
| A24008-27 | Test Box - Hydr Motor Driven Gen. Control Unit | | Replaced by A24008-37 | |
| A24008-37 | Test Box - Hydr Motor Driven Gen. Control Unit | | | |
| A24011-1 | Hoist Adapter Assembly - IDG | | | |
| A24012-1 | Dispatch Kit - IDG, P&W engines | | | |
| A25001-1 | Replacement Equipment - Air Chiller, FWD Galley | | Replaced by A25001-33 | |
| A25001-33 | Replacement Equipment - Air Chiller, FWD Galley | | | |
| A25002-1 | Slide Bar - Aft Galley Air Chiller | | | |
| A25003-12 | Simulator - Door Opening Actuator, Off Wing Escape | | Replaced by A25003-15 | |
| A25003-15 | Simulator - Door Opening Actuator, Off Wing Escape | | Replaced by A25003-20 | |
| A25003-20 | Simulator - Door Opening Actuator, Off Wing Escape | | Replaced by A25003-24 | |
| A25003-24 | Simulator - Door Opening Actuator, Off Wing Escape | | | |
| A25003-8 | Simulator - Door Opening Actuator, Off Wing Escape | | Replaced by A25003-15 | |
| A25004-1 | Simulator Eqpmt - Off-Wing Esc. Slide Door Latch | | | |
| A25005-1 | Simulator - Gas Pressure Vessel | | Replaced by A25005-21 | |
| A25005-21 | Simulator - Gas Pressure Vessel | | Replaced by A25005-29 | |
| A25005-29 | Simulator - Gas Pressure Vessel | | | |
| A25008-1 | Installation Equipment - Luggage Bin Snubber | | | |
| A25009-1 | Removal Tool - Ball Transfer Unit | | Replaced by A25009-2 | |
| A25009-2 | Removal Tool - Ball Transfer Unit | | | |
| A25010-1 | Wrench Set - Stowage Bin Release | | Replaced by A25013-1 | |
| A25011-1 | Wrench - Integrator, Off-Wing Escape System | | Replaced by A25011-2 | |
| A25011-2 | Wrench - Integrator, Off-Wing Escape System | | | |
| A25012-1 | Electrical Test Eqpmnt - Off-Wing Esc. Slide Systm | | Replaced by A25012-19 | |
| A25012-19 | Electrical Test Eqpmnt - Off-Wing Esc. Slide Systm | | Replaced by A25012-29 | |
| A25012-29 | Electrical Test Eqpmnt - Off-Wing Esc. Slide Systm | | | |
| A25013-1 | Wrench Set - Stowage Bin Release | | Replaced by A25018-1 | |
| A25014-10 | Simulator Eqpmt - Latch Opening, Off-wing Esc. Sys | | Replaced by A25014-16 | |
| A25014-16 | Simulator Eqpmt - Latch Opening, Off-wing Esc. Sys | | Replaced by A25014-19 | |
| A25014-19 | Simulator Eqpmt - Latch Opening, Off-wing Esc. Sys | | Replaced by A25014-29 | |
| A25014-29 | Simulator Eqpmt - Latch Opening, Off-wing Esc. Sys | | | |
| A25016-1 | Safety Equipment - Escape System, Off Wing | | | |
| A25017-1 | Adjustor - Friction Ball Catch | | | |
| A25018-1 | Wrench Set - Stowage Bin Release | | Replaced by A25018-10 | |
| A25018-10 | Wrench Set - Stowage Bin Release | | | |
| A25019-1 | Gage - Actuator, Latch Opening, Off-wing Esc. Syst | | | |
| A25020-1 | Gage-Inspection, Seat Track, Flight Crew | | Replaced by A25020-4 | |
| A25020-4 | Gage-Inspection, Seat Track, Flight Crew | | Replaced by A25020-8 | |
| A25020-8 | Gage-Inspection, Seat Track, Flight Crew | | | |
| A25021-1 | Push Plate - Spring Load APU | | | |
| A25022-1 | Test Equipment - PDU, Guides, and Rollout Stops | | | |
| A26001-1 | Adapter Cable, Test, Fire Extinguisher | | Replaced by A26001-69 | |
| A26001-106 | Adapter Cable, Test, Fire Extinguisher | | Replaced by A26001-133 | |
| A26001-131 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-132 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-133 | Adapter Cable, Test, Fire Extinguisher | | Replaced by A26001-106 | |
| A26001-134 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-135 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-136 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-137 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-138 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-139 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-144 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-145 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-148 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-165 | Elec. Test Eqmt - Bottle Squib, Fire Extinguisher | | Replaced by A26001-174 | |
| A26001-174 | Elec. Test Eqmt - Bottle Squib, Fire Extinguisher | | Replaced by A26001-187 | |
| A26001-175 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-176 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-182 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-187 | Elec. Test Eqmt - Bottle Squib, Fire Extinguisher | | | |
| A26001-24 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-3 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-4 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-41 | Adapter Cable, Test, Fire Extinguisher | | Replaced by A26001-69 | |
| A26001-5 | Adapter Cable, Test, Fire Extinguisher | | | |
| A26001-69 | Adapter Cable, Test, Fire Extinguisher | | Replaced by A26001-72 | |
| A26001-72 | Adapter Cable, Test, Fire Extinguisher | | Replaced by A26001-106 | |
| A26002-1 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | Replaced by A26002-17 | |
| A26002-17 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | Replaced by A26002-23 | |
| A26002-17 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | Replaced by A26002-28 | |
| A26002-23 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | Replaced by A26002-28 | |
| A26002-28 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | Replaced by A26002-51 | |
| A26002-36 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | | |
| A26002-51 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | Replaced by A26002-54 | |
| A26002-54 | Test Box - Time Delay, Cargo Fire Extingshr Bottle | | | |
| A26003-1 | Test Equipment - Regulator, Cargo Fire Extinguishg | | Replaced by A26003-7 | |
| A26003-10 | Test Equipment - Regulator, Cargo Fire Extinguishg | | | |
| A26003-7 | Test Equipment - Regulator, Cargo Fire Extinguishg | | Replaced by A26003-10 | |
| A26004-1 | Plug Eqpmt - Dischrg Nozzle, Cargo B Fire Extinghr | | | |
| A26005-1 | Platform - Maintenance, Cargo Sidewall | | | |
| A27001-1 | PCA Gages - Inbd/Outbd Aileron, Rudder, Elevator | | | |
| A27001-2 | PCA Gages - Inbd/Outbd Aileron, Rudder, Elevator | | | |
| A27001-3 | PCA Gages - Inbd/Outbd Aileron, Rudder, Elevator | | | |
| A27001-4 | PCA Gages - Inbd/Outbd Aileron, Rudder, Elevator | | | |
| A27003-13 | Lock Set - Actuator, Rudder | | | |
| A27003-16 | Lock Set - Actuator, Rudder | | | |
| A27003-23 | Lock Set - Actuator, Rudder | | Replaced by A27003-13 | |
| A27004-1 | Hoist Adapter - Leading Edge Slat Drive | | | |
| A27004-2 | Hoist Adapter - Leading Edge Slat Drive | | | |
| A27005-1 | Lock - Outboard Aileron | | | |
| A27006-17 | Hoist Equipment - Horizontal Stabilizer Trim Act | | Replaced by A27006-41 | |
| A27006-33 | Hoist Equipment - Horizontal Stabilizer Trim Act | | Replaced by A27006-41 | |
| A27006-41 | Hoist Equipment - Horizontal Stabilizer Trim Act | | | |
| A27007-1 | Ground Lock - Leading Edge Slats | | | |
| A27009-1 | Lock - Trailing Edge Flaps | | Replaced by A27009-7 | |
| A27009-7 | Lock - Trailing Edge Flaps | | | |
| A27010-11 | Lock Set - Circuit Breaker | | | |
| A27010-15 | Lock Set - Circuit Breaker | | | |
| A27012-20 | Sling Equipment - Inbd/Outbd Elevator Segment | | Replaced by A27012-30 | |
| A27012-30 | Sling Equipment - Inbd/Outbd Elevator Segment | | | |
| A27013-1 | Deactivation Equipment - Inboard Aileron | | | |
| A27015-1 | Rem/Inst Sling Equipment - Inb/Outb Aileron | | | |
| A27016-1 | Sling Equipment - Inboard Trainling Edge Flap | | Replaced by A27016-21 | |
| A27016-21 | Sling Equipment - Inboard Trainling Edge Flap | | Replaced by A27016-22 | |
| A27016-22 | Sling Equipment - Inboard Trainling Edge Flap | | Replaced by A27016-27 | |
| A27016-27 | Sling Equipment - Inboard Trainling Edge Flap | | | |
| A27017-1 | Sling Equipment - Leading Edge Slat | | Replaced by A27017-41 | |
| A27017-41 | Sling Equipment - Leading Edge Slat | | | |
| A27019-1 | Restraint - Aft Flap to INBD Trailing Edge Flap | | Replaced by A27019-8 | |
| A27019-8 | Restraint - Aft Flap to INBD Trailing Edge Flap | | | |
| A27020-1 | Straightedge - Control Wheel | | | |
| A27021-1 | Adapter Equipment - Control Wheel | | Replaced by A27021-96 | |
| A27021-29 | Adapter Equipment - Control Wheel | | | |
| A27021-55 | Adapter Equipment - Control Wheel | | Replaced by A27021-98 | |
| A27021-64 | Adapter Equipment - Control Wheel | | Replaced by A27021-98 | |
| A27021-83 | Adapter Equipment - Control Wheel | | Replaced by A27021-98 | |
| A27021-96 | Adapter Equipment - Control Wheel | | | |
| A27021-98 | Adapter Equipment - Control Wheel | | | |
| A27022-75 | Sling Equipment - Rudder Inst/Removal | | Replaced by A27022-81 | |
| A27022-81 | Sling Equipment - Rudder Inst/Removal | | | |
| A27023-1 | Spacer Kit - Inbd/Outb Slat Installation | | Replaced by A27023-11 | |
| A27023-11 | Spacer Kit - Inbd/Outb Slat Installation | | Replaced by A27023-17 | |
| A27023-17 | Spacer Kit - Inbd/Outb Slat Installation | | Replaced by A27023-18 | |
| A27023-18 | Spacer Kit - Inbd/Outb Slat Installation | | Replaced by A27023-22 | |
| A27023-19 | Spacer Kit - Inbd/Outb Slat Installation | | Alternative of 2MIT114T4000 | |
| A27023-22 | Spacer Kit - Inbd/Outb Slat Installation | | | |
| A27023-3 | Spacer Kit - Inbd/Outb Slat Installation | | Alternative of MIT114T3000 | |
| A27024-1 | Rigging Bar - Aileron | | Replaced by A27024-29 | |
| A27024-2 | Rigging Bar - Aileron | | Replaced by A27024-47 | |
| A27024-29 | Rigging Bar - Aileron | | Replaced by A27024-31 | |
| A27024-31 | Rigging Bar - Aileron | | | |
| A27024-47 | Rigging Bar - Aileron | | Replaced by A27024-55 | |
| A27024-55 | Rigging Bar - Aileron | | | |
| A27025-1 | Rigging Equipment - Force Transducer, Elevtr Cntrl | | | |
| A27026-1 | Hoist Bracket - Fishpole Hoist Flpa PDU | | Replaced by A27026-7 | |
| A27026-7 | Hoist Bracket - Fishpole Hoist Flpa PDU | | | |
| A27027-1 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-14 | |
| A27027-14 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-21 | |
| A27027-21 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-30 | |
| A27027-30 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-34 | |
| A27027-34 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-40 | |
| A27027-34 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-47 | |
| A27027-40 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-48 | |
| A27027-47 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27027-53 | |
| A27027-48 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27071-84 | |
| A27027-53 | Sling Equipment - Outboard Trailing Edge Flap | | | |
| A27027-54 | Sling Equipment - Outboard Trailing Edge Flap | | | |
| A27027-90 | Sling Equipment - Outboard Trailing Edge Flap | | Replaced by A27071-123 | |
| A27028-1 | Check Fixture - Aielron Contrl Load Limiter Spring | | Replaced by A27028-11 | |
| A27028-11 | Check Fixture - Aielron Contrl Load Limiter Spring | | | |
| A27029-28 | Rem/Inst Fixture - Load Limit Aileron Cntrl Spring | | | |
| A27030-38 | Test Box - Power Supply, CSEU | | Replaced by A27030-42 | |
| A27030-42 | Test Box - Power Supply, CSEU | | Replaced by A27030-43 | |
| A27030-43 | Test Box - Power Supply, CSEU | | Replaced by A27030-48 | |
| A27030-48 | Test Box - Power Supply, CSEU | | Replaced by A27030-51 | |
| A27030-51 | Test Box - Power Supply, CSEU | | Replaced by A27030-66 | |
| A27030-58 | Test Box - Power Supply, CSEU | | | |
| A27030-66 | Test Box - Power Supply, CSEU | | | |
| A27035-1 | Adapter - Rudder/Elevator Feel Actuator Cylinder | | | |
| A27036-16 | Test Box - FSEU Power Supply/Yaw Damper EMI Filter | | | |
| A27036-16 | Breakout Box - Yaw Damper EMI Filter | | Replaced by A27036-22 | |
| A27036-22 | Test Box - FSEU Power Supply/Yaw Damper EMI Filter | | | |
| A27037-1 | Test Equipment - Outboard Aileron Lockout Mechnsm | | | |
| A27038-1 | Breakout Box - Printed Circuit Card | | | |
| A27038-10 | Breakout Box - Printed Circuit Card | | | |
| A27038-20 | Breakout Box - Printed Circuit Card | | | |
| A27038-6 | Breakout Box - Printed Circuit Card | | | |
| A27039-1 | Breakout Box - Bench Test | | Replaced by A27039-26 | |
| A27039-19 | Breakout Box - Bench Test | | Replaced by A27039-27 | |
| A27039-26 | Breakout Box - Bench Test | | | |
| A27039-27 | Breakout Box - Bench Test | | | |
| A27039-9 | Breakout Box - Bench Test | | Replaced by A27039-19 | |
| A27040-1 | Check Equipment - Bearing Width | | | |
| A27040-18 | Check Equipment - Bearing Width | | | |
| A27041-1 | Test Equipment - Elevator Feel & Centering Unit | | Replaced by A27041-34 | |
| A27041-104 | Test Equipment - Elevator Feel & Centering Unit | | Replaced by A27041-142 | |
| A27041-142 | Test Equipment - Elevator Feel & Centering Unit | | Replaced by A27041-170 | |
| A27041-142 | Test Equipment - Elevator Feel & Centering Unit | | Replaced by A27041-177 | |
| A27041-170 | Test Equipment - Elevator Feel & Centering Unit | | | |
| A27041-177 | Test Equipment - Elevator Feel & Centering Unit | | | |
| A27041-34 | Test Equipment - Elevator Feel & Centering Unit | | | |
| A27042-1 | Functional Test Equipment - Sploiler Actuator | | | |
| A27043-1 | Test Eqpmt Fixture - Inbd/Outbd Spoiler Act | | | |
| A27044-33 | Test Box - Converter, CSEU power Supply | | Replaced by A27044-38 | |
| A27044-35 | Test Box - Converter, CSEU power Supply | | Replaced by A27044-38 | |
| A27044-38 | Test Box - Converter, CSEU power Supply | | Replaced by A27044-44 | |
| A27044-44 | Test Box - Converter, CSEU power Supply | | Replaced by A27044-53 | |
| A27044-53 | Test Box - Converter, CSEU power Supply | | | |
| A27045-1 | Test Box - Noise, CSEU Power Supply | | Replaced by A27045-16 | |
| A27045-16 | Test Box - Noise, CSEU Power Supply | | | |
| A27046-1 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-141 | |
| A27046-140 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-141 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-191 | |
| A27046-160 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-161 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-176 | |
| A27046-162 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-177 | |
| A27046-163 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-192 | |
| A27046-176 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-177 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-191 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-192 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-2 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-140 | |
| A27046-3 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-4 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-5 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-99 | |
| A27046-7 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-160 | |
| A27046-8 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27046-81 | Test Fixture - Power Drive Components Flight Cntrl | | Replaced by A27046-163 | |
| A27046-99 | Test Fixture - Power Drive Components Flight Cntrl | | | |
| A27047-1 | Test Block - Spoiler Actuator Valve Cartridge | | | |
| A27048-1 | Fixture - Check, Gearbox Backlash | | | |
| A27048-2 | Fixture - Check, Gearbox Backlash | | | |
| A27048-3 | Fixture - Check, Gearbox Backlash | | | |
| A27048-40 | Fixture - Check, Gearbox Backlash | | | |
| A27049-1 | Check Fixture - LE Slat Angle Gearbox Backlash | | | |
| A27051-1 | Tool Set - TE Flap Drive & LE Slat Drive Gearboxes | | Replaced by A27051-31 | |
| A27051-31 | Tool Set - TE Flap Drive & LE Slat Drive Gearboxes | | | |
| A27052-1 | Test Box - Regulator, CSEU Power Supply | | | |
| A27053-23 | Test Box, Monitor, CSEU Poer Supply | | Replaced by A27053-26 | |
| A27053-26 | Test Box - Monitor, CSEU Power Supply | | Replaced by A27053-29 | |
| A27053-29 | Test Box - Monitor, CSEU Power Supply | | | |
| A27053-32 | Test Box - Monitor, CSEU Power Supply | | | |
| A27054-1 | Fixture-Holding, Gear Assembly, LE Slat Drive | | Replaced by A27054-14 | |
| A27054-14 | Fixture-Holding, Gear Assembly, LE Slat Drive | | | |
| A27055-1 | Fixture - TE Flap Drive Worm Gear Shim Thickness | | | |
| A27057-1 | Protractor Bracket Eqpmt - Feel Centering & Trim | | Replaced by A27057-13 | |
| A27057-1 | Protractor Bracket Eqpmt - Feel Centering & Trim | | Replaced by A27057-9 | |
| A27057-13 | Protractor Bracket Eqpmt - Feel Centering & Trim | | | |
| A27057-9 | Protractor Bracket Eqpmt - Feel Centering & Trim | | Replaced by A27057-13 | |
| A27058-57 | Test Equipment - Elevator Feel & Centering Unit | | Replaced by A27058-60 | |
| A27058-60 | Jig Equipment - Elevator Feel & Centring Unit | | | |
| A27059-1 | Breakout Box - Choper/Regulator Power Supply, CSEU | | | |
| A27060-1 | Jig Eqpment - Inbd & Outbd LE Slat & TE Flap Drive | | Replaced by A27060-11 | |
| A27060-11 | Jig Eqpment - Inbd & Outbd LE Slat & TE Flap Drive | | | |
| A27061-1 | Tool Set - Trailing Edge Rotary Actuator | | Replaced by A27061-44 | |
| A27061-44 | Tool Set - Trailing Edge Rotary Actuator | | | |
| A27061-46 | Tool Set - Trailing Edge Rotary Actuator | | Replaced by A27061-54 | |
| A27061-54 | Tool Set - Trailing Edge Rotary Actuator | | | |
| A27062-1 | Tool Set - Stabilizer Trim Drive | | | |
| A27063-71 | Breakout Box - Position Sensors, Flght Cntl Riggng | | Replaced by A27063-91 | |
| A27063-91 | Breakout Box - Position Sensors, Flght Cntl Riggng | | | |
| A27067-1 | Wrench - Control Lever, Speed Brake | | | |
| A27070-1 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | Replaced by A27070-18 | |
| A27070-18 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | Replaced by A27070-54 | |
| A27070-48 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | | |
| A27070-54 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | Replaced by A27070-61 | |
| A27070-61 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | | |
| A27070-65 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | | |
| A27070-76 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | Replaced by A27070-80 | |
| A27070-80 | Bearing Inst Eqpmnt - Rotary Bearing Inst Eqpmnt | | | |
| A27071-123 | Test Equipment - Rotary Actuator TE Flap | | Replaced by A27079-78 | |
| A27071-48 | Test Equipment - Rotary Actuator TE Flap | | | |
| A27071-84 | Test Equipment - Rotary Actuator TE Flap | | | |
| A27071-90 | Test Equipment - Rotary Actuator TE Flap | | | |
| A27072-42 | Test Fixture - Stabilizer Trim Drive Mechanism | | | |
| A27072-43 | Test Fixture - Stabilizer Trim Drive Mechanism | | | |
| A27072-44 | Test Fixture - Stabilizer Trim Drive Mechanism | | | |
| A27072-53 | Test Fixture - Stabilizer Trim Drive Mechanism | | | |
| A27072-55 | Test Fixture - Stabilizer Trim Drive Mechanism | | | |
| A27073-1 | Socket - Thin Wall, Gearbox, Inbd LE Slat Drive | | | |
| A27074-1 | Lock Set - Inb & Outb Flap Linkage Trailing Edge | | Replaced by A27074-128 | |
| A27074-120 | Lock Set - Inb & Outb Flap Linkage Trailing Edge | | Replaced by A27074-128 | |
| A27074-128 | Lock Set - Inb & Outb Flap Linkage Trailing Edge | | Replaced by A27074-146 | |
| A27074-146 | Lock Set - Inb & Outb Flap Linkage Trailing Edge | | | |
| A27075-1 | Wrench - Spoiler Actuator Assembly Adjustment | | | |
| A27077-1 | Adapter - Leading Edge Slat drive | | | |
| A27078-7 | Spline Adapters - LE Slat Drive Rot Act & Gearbox | | | |
| A27079-1 | Test Equipment - PDU, TE Flap and LE Slat Drive | | Replaced by A27079-71 | |
| A27079-71 | Test Equipment - PDU, TE Flap and LE Slat Drive | | | |
| A27079-78 | Test Equipment - PDU, TE Flap and LE Slat Drive | | Replaced by A27079-89 | |
| A27079-89 | Test Equipment - PDU, TE Flap and LE Slat Drive | | Replaced by A27079-96 | |
| A27079-96 | Test Equipment - PDU, TE Flap and LE Slat Drive | | | |
| A27081-1 | Readout and Control Eqpmt - Functional Test Stands | | | |
| A27081-2 | Readout and Control Eqpmt - Functional Test Stands | | | |
| A27085-1 | Sling Assembly - Stabilizer Trim Drive Mechanism | | | |
| A27085-1 | Test Box - Analog Printed Circuit, Rudder Ratio | | | |
| A27086-1 | Support Fixture - Elevator Slave Linkage | | Replaced by A27086-10 | |
| A27086-10 | Support Fixture - Elevator Slave Linkage | | | |
| A27088-6 | Link - Dummy Trim Actuator, Aileron | | | |
| A27089-5 | Gage - Rigging, LE Slat Outb Wing | | Replaced by A27089-9 | |
| A27089-9 | Gage - Rigging, LE Slat Outb Wing | | | |
| A27092-106 | Actuator/Deactuator Set Proximity Sensors | | | |
| A27092-61 | Actuator/Deactuator Set Proximity Sensors | | Replaced by A27092-84 | |
| A27092-84 | Actuator/Deactuator Set Proximity Sensors | | Replaced by A27092-106 | |
| A27093-1 | Test Equipment -TE Flaps Asymmetry Fault Isolation | | | |
| A27093-23 | Test Equipment -TE Flaps Asymmetry Fault Isolation | | Replaced by A27093-27 | |
| A27093-27 | Test Equipment -TE Flaps Asymmetry Fault Isolation | | | |
| A27094-1 | Spacer Set - Preload, Leading Edge Slat Rigging | | Replaced by A27094-5 | |
| A27094-5 | Spacer Set - Preload, Leading Edge Slat Rigging | | | |
| A27095-1 | Scale - Control Column Angle | | Replaced by A27095-10 | |
| A27095-10 | Scale - Control Column Angle | | | |
| A27096-1 | Breakout Box - Spoiler Pnl Position Monitor & Rely | | | |
| A27097-1 | Adapter, Protractor, Thrust Reverser Lever | | | |
| A27098-1 | Test Box - Bite Diplay PCA, WEU | | | |
| A27099-1 | Shaft Clamp - TE Flap Drive | | | |
| A27100-1 | Test Box - Stick Nudger | | | |
| A27101-1 | Wrench - Adjustment, Inb LE Slats | | Replaced by A27101-5 | |
| A27101-5 | Wrench - Adjustment, Inb LE Slats | | | |
| A27102-1 | Adapter - LE Slat & TE Flap, Manual Drive | | Replaced by A27102-5 | |
| A27102-5 | Adapter - LE Slat & TE Flap, Manual Drive | | Replaced by A27102-7 | |
| A27102-7 | Adapter - LE Slat & TE Flap, Manual Drive | | | |
| A27105-1 | Auxiliary Detent - Flap Adjustment Assembly | | Replaced by A27105-6 | |
| A27105-6 | Auxiliary Detent - Flap Adjustment Assembly | | Replaced by A27105-9 | |
| A27105-9 | Auxiliary Detent - Flap Adjustment Assembly | | | |
| A27106-1 | Bushing Puller - Outboard Aileron Actuator | | | |
| A27107-1 | Dummy Link Set - Flap Load Relief Actuator | | | |
| A27108-1 | Lock Set - Spoiler Actuator | | Replaced by A27108-10 | |
| A27108-10 | Lock Set - Spoiler Actuator | | Replaced by A27108-13 | |
| A27108-13 | Lock Set - Spoiler Actuator | | | |
| A27109-1 | Rigging Bar - Ratio Changer Install., Rudder Cntrl | | | |
| A27110-1 | Mount Equipment - Inboard Aileron Rigging Bar | | | |
| A27110-20 | Mount Equipment - Inboard Aileron Rigging Bar | | | |
| A27111-1 | Lock Equipment - Elevator Actuator | | Replaced by A27111-11 | |
| A27111-11 | Lock Equipment - Elevator Actuator | | | |
| A27112-1 | Rigging Equipment - LE Slat Position Sensor Switch | | | |
| A27114-1 | Rem/Inst Equipment, Pivot Brg Horizontal Stabilizr | | | |
| A27115-26 | Test Equipment - Outboard Aileron Lockout Actuator | | Replaced by A27115-34 | |
| A27115-34 | Test Equipment - Outboard Aileron Lockout Actuator | | Replaced by A27115-41 | |
| A27115-36 | Test Equipment - Outboard Aileron Lockout Actuator | | Replaced by A27115-41 | |
| A27115-41 | Test Equipment - Outboard Aileron Lockout Actuator | | | |
| A27116-1 | Sling - Outboard Slat PDU | | | |
| A27117-1 | Test Equipment - LE Slat 5 & 8, Inbd Offset Gearbx | | | |
| A27118-1 | Lock Equipment - Inb & Outb TE Flap Linkage | | Replaced by A27118-90 | |
| A27118-90 | Lock Equipment - Inb & Outb TE Flap Linkage | | | |
| A27119-1 | Holding Fixture Eqpment - Gear Assy, LE Slat Drive | | | |
| A27120-1 | Dis-/Assembly Equipment - Rotary Actuator TE Flap | | Replaced by A27120-43 | |
| A27120-43 | Dis-/Assembly Equipment - Rotary Actuator TE Flap | | | |
| A27121-1 | Tool Set - Seal Installation | | | |
| A27122-1 | Wrench - Bearing Retaining Nut, Inbd Flap Linkage | | | |
| A27123-1 | Measurement Eqpmnt Bevel Gear Teeth, Stab Trim Act | | | |
| A27124-1 | Force Equipment - Rudder Freeplay Check | | | |
| A27125-1 | Measurement Tool - Rudder & Elevator Pwr Cntrl Act | | | |
| A28001-1 | Hose set, Main and Overrid Pump Defueling | | | |
| A28002-1 | Drain Hose, Fuel System Sump | | Replaced by A28002-6 | |
| A28002-1 | Drain Hose, Fuel System Sump | | Replaced by J28013-1 | |
| A28002-6 | Drain Hose, Fuel System Sump | | | |
| A28003-1 | Ventilation Equipment, Fuel Tank | | Replaced by A28003-43 | A28003-77 |
| A28003-43 | Ventilation Equipment, Fuel Tank | | | |
| A28004-1 | Check Fixture, Surge Tank Pressure Relief Valve | | | |
| A28005-22 | Tool | | Replaced by A28005-35 | |
| A28005-24 | Adapter Assembly | | | |
| A28005-35 | Test Eqpmnt, Leak & Pressure, APU Fuel Line Shroud | | Replaced by A28005-24 | |
| A28005-35 | Test Eqpmnt, Leak & Pressure, APU Fuel Line Shroud | | Replaced by A28005-50 | |
| A28005-42 | Test Hose | | Replaced by A28005-50 | |
| A28005-50 | Test Hose | | | |
| A28005-8 | Tool | | Replaced by A28005-35 | |
| A28006-1 | Test Box, Fuel Level Sensors Surge Tank | | | |
| A28006-22 | Test Box, Fuel Level Sensors Surge Tank | | | |
| A28006-27 | Test Box, Fuel Level Sensors Surge Tank | | | |
| A28007-1 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-39 | |
| A28007-1 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-40 | |
| A28007-2 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-39 | |
| A28007-2 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-40 | |
| A28007-27 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-39 | |
| A28007-27 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-40 | |
| A28007-28 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-39 | |
| A28007-28 | Test Box, Fuel Quantity Indicating System | | Replaced by A28007-40 | |
| A28007-39 | Test Box, Fuel Quantity Indicating System | | | |
| A28007-40 | Test Box, Fuel Quantity Indicating System | | | |
| A28008-1 | Drain Hose - Sump Valve, Center Aux. Fuel Tanks | | Replaced by A28008-8 | |
| A28008-8 | Drain Hose - Sump Valve, Center Aux. Fuel Tanks | | | |
| A28009-1 | Extender Board, Surge Tank Fuel Level Sensor | | Replaced by A28009-8 | |
| A28009-13 | Extender Board, Surge Tank Fuel Level Sensor | | | |
| A28009-8 | Extender Board, Surge Tank Fuel Level Sensor | | Replaced by A28009-13 | |
| A28010-1 | Spanner Wrench, Fuel Sump Drain Valve | | Replaced by A28012-1 | |
| A28010-2 | Spanner Wrench, Fuel Sump Drain Valve | | | |
| A28011-1 | Test Eqmt, Pressure/Leakage, Fuel Lines & Fittings | | Replaced by A28011-48 | |
| A28011-1 | Test Eqmt, Pressure/Leakage, Fuel Lines & Fittings | | Replaced by A28011-49 | |
| A28011-1 | Test Eqmt, Pressure/Leakage, Fuel Lines & Fittings | | Replaced by A28011-50 | |
| A28011-48 | Test Eqmt, Pressure/Leakage, Fuel Lines & Fittings | | | |
| A28011-49 | Test Eqmt, Pressure/Leakage, Fuel Lines & Fittings | | | |
| A28011-50 | Test Eqmt, Pressure/Leakage, Fuel Lines & Fittings | | | |
| A28012-1 | Spanner Wrench, Fuel Sump Drain Valve | | | |
| A28013-1 | Adapter equipment, Air Supply, Surge Tank | | Replaced by A28013-10 | |
| A28013-1 | Adapter equipment, Air Supply, Surge Tank | | Replaced by A28013-11 | |
| A28013-10 | Adapter equipment, Air Supply, Surge Tank | | | |
| A28013-11 | Adapter equipment, Air Supply, Surge Tank | | | |
| A29001-1 | Hoist Adapter, Air Driven Hydraulic Pump | | | |
| A29002-6 | Locking Pin, Valve, Hydr Reservoir Press Shutoff | | | |
| A29003-1 | Tool Set, Hydraulic Filter Overhaul | | Replaced by A29003-49 | |
| A29003-49 | Tool Set, Hydraulic Filter Overhaul | | | |
| A29004-1 | Tool Set, Hydraulic Filter Module Overhaul | | | |
| A29005-1 | Sealing Cap, Pressure Transmitter Mount | | | |
| A29006-19 | Test Box, Pressure/Thermal Switch | | | |
| A30002-1 | Plug Eqmt, Thrml Anti-Icing Duct, Wng Prss Swtch T | | | |
| A30003-1 | Breakout Box, Viewport Heater | | | |
| A31003-1 | Test Box, WEU Power Supply | | Replaced by A31003-29 | |
| A31003-1 | Test Box, WEU Power Supply | | Replaced by A31003-34 | |
| A31003-25 | Test Box, WEU Power Supply | | Replaced by A31003-29 | |
| A31003-25 | Test Box, WEU Power Supply | | Replaced by A31003-33 | |
| A31003-29 | Test Box, WEU Power Supply | | Replaced by A31003-34 | |
| A31003-33 | Test Box, WEU Power Supply | | | |
| A31003-34 | Test Box, WEU Power Supply | | | |
| A31004-1 | Breakout Box, WEU Power Supply and Monitor | | | |
| A31005-1 | Test Box, WEU Power Supply Noise | | Replaced by A31005-14 | |
| A31005-14 | Test Box, WEU Power Supply Noise | | | |
| A31006-5 | Shorting Module, Master Warning PC Assy | | Replaced by A31006-7 | |
| A31006-7 | Shorting Module, Master Warning PC Assy | | | |
| A31007-1 | Adapter Cable, Digital Flight Recorder Sstm Tester | | | |
| A31007-11 | Adapter Cable, Digital Flight Recorder Sstm Tester | | Replaced by A31007-59 | |
| A31007-16 | Adapter Cable, Digital Flight Recorder Sstm Tester | | Replaced by A31007-30 | |
| A31007-30 | Adapter Cable, Digital Flight Recorder Sstm Tester | | | |
| A31007-49 | Adapter Cable, Digital Flight Recorder Sstm Tester | | | |
| A31007-59 | Adapter Cable, Digital Flight Recorder Sstm Tester | | | |
| A31008-1 | Test Cable, WEU Power Supply | | | |
| A31010-1 | Breakout Box, Power Supply Unit, WEU | | | |
| A32001-1 | Brake Disconnect Assembly, Flight Dispatch | | Replaced by A32080-1 | |
| A32002-1 | Spring Extender, Drag Strut, MLG | | Replaced by A32002-14 | |
| A32002-14 | Spring Extender, Drag Strut, MLG | | | |
| A32004-1 | Wrench Adapter, Gland Nut, MLG | | | |
| A32004-4 | Wrench Adapter, Gland Nut, MLG | | | |
| A32004-5 | Wrench Adapter, Gland Nut, MLG | | | |
| A32005-43 | Replacement Equipment, Seal, Lower BRG, MLG | | Replaced by A32005-54 | |
| A32005-54 | Replacement Equipment, Seal, Lower BRG, MLG | | | |
| A32006-75 | Sling Equipment, Retract Actuator, MLG | | Replaced by A32006-77 | |
| A32006-77 | Sling Equipment, Retract Actuator, MLG | | | |
| A32007-16 | Protector Equipment, Axle & Axle Thread, MLG | | Replaced by A32007-17 | |
| A32007-16 | Protector Equipment, Axle & Axle Thread, MLG | | Replaced by A32098-1 | |
| A32007-16 | Protector Equipment, Axle & Axle Thread, MLG | | Replaced by A32098-12 | |
| A32007-17 | Protector Equipment, Axle & Axle Thread, MLG | | Replaced by A32098-12 | |
| A32008-1 | Sling Equipment, MLG Components | | Replaced by A32008-51 | |
| A32008-44 | Sling Equipment, MLG Components | | Replaced by A32008-53 | |
| A32008-51 | Sling Equipment, MLG Components | | | |
| A32008-53 | Sling Equipment, MLG Components | | | |
| A32010-1 | Pin Puller, Retract Actuator, MLG | | | |
| A32011-1 | Puller, Trunnion Pins, NLG | | | |
| A32012-1 | Wrench, Wheel Retaining Nut, MLG | | Replaced by A32012-12 | |
| A32012-12 | Wrench, Wheel Retaining Nut, MLG | | Replaced by A32012-13 | |
| A32012-13 | Wrench, Wheel Retaining Nut, MLG | | | |
| A32012-6 | Wrench, Wheel Retaining Nut, MLG | | Replaced by A32012-13 | |
| A32012-9 | Wrench, Wheel Retaining Nut, MLG | | Replaced by A32012-13 | |
| A32013-1 | Pin Puller, Upper Drag Brace, NLG | | | |
| A32014-1 | Downlock, MLG and NLG | | | |
| A32014-2 | Downlock, MLG and NLG | | | |
| A32015-1 | Installation/Removal Tool, Downlock, MLG and NLG | | Replaced by A32015-9 | |
| A32015-9 | Installation/Removal Tool, Downlock, MLG and NLG | | | |
| A32016-13 | Pin Puller, Brake Rod, MLG | | Replaced by A32016-17 | |
| A32016-17 | Pin Puller, Brake Rod, MLG | | | |
| A32018-1 | Spring Extender, Lock Link, NLG | | | |
| A32020-1 | Hoist Adapter, Drag Strut, NLG | | | |
| A32021-1 | Wrench Adapter, Gland Nut, NLG | | | |
| A32022-1 | Protector, Axle, NLG | | | |
| A32023-1 | Sling, Retract Actuator, NLG | | | |
| A32025-1 | Wrench Adapter, Wheel Retaining Axle Nut, NLG | | Replaced by A32101-1 | |
| A32026-1 | Removal/Installation Equipment, Trunnion Pin, MLG | | Replaced by A32026-60 | |
| A32026-2 | Removal/Installation Equipment, Trunnion Pin, MLG | | Replaced by A32026-60 | |
| A32026-60 | Removal/Installation Equipment, Trunnion Pin, MLG | | | |
| A32027-153 | Pump, Retraction/Extention Landing Gear Actuator | | Replaced by A32027-176 | |
| A32027-166 | Pump, Retraction/Extention Landing Gear Actuator | | Replaced by A32027-178 | |
| A32027-175 | Pump, Retraction/Extention Landing Gear Actuator | | Replaced by A32027-178 | |
| A32027-176 | Pump, Retraction/Extention Landing Gear Actuator | | Replaced by A32027-178 | |
| A32027-178 | Pump, Retraction/Extention Landing Gear Actuator | | | |
| A32027-48 | Pump, Retraction/Extention Landing Gear Actuator | | Replaced by A32027-53 | |
| A32027-53 | Pump, Retraction/Extention Landing Gear Actuator | | | |
| A32027-90 | Pump, Retraction/Extention Landing Gear Actuator | | | |
| A32028-6 | Retention Strap, Inner Cylinder, MLG and NLG | | | |
| A32029-1 | Replacement Equipment, Lower Seal, NLG | | Replaced by A32029-48 | |
| A32029-26 | Replacement Equipment, Lower Seal, NLG | | | |
| A32029-48 | Replacement Equipment, Lower Seal, NLG | | Replaced by A32029-50 | |
| A32029-50 | Replacement Equipment, Lower Seal, NLG | | | |
| A32030-10 | Lock, MLG Door | | | |
| A32030-12 | Lock, MLG Door | | Replaced by A32030-21 | |
| A32030-18 | Lock, MLG Door | | | |
| A32030-21 | Lock, MLG Door | | | |
| A32030-4 | Lock, MLG Door | | | |
| A32030-6 | Lock, MLG Door | | Replaced by A32030-18 | |
| A32031-1 | Turnbuckle, Truck Position Actuator, MLG | | Replaced by A32031-4 | |
| A32031-4 | Turnbuckle, Truck Position Actuator, MLG | | Replaced by A32031-5 | |
| A32031-5 | Turnbuckle, Truck Position Actuator, MLG | | | |
| A32032-38 | Removal/Installation Equipment, MLG | | Replaced by A32032-52 | |
| A32032-39 | Removal/Installation Equipment, MLG | | Replaced by A32032-65 | |
| A32032-52 | Removal/Installation Equipment, MLG | | Replaced by A32032-64 | |
| A32032-64 | Removal/Installation Equipment, MLG | | Alternative of A32032-65 | |
| A32032-65 | Removal/Installation Equipment, MLG | | | |
| A32033-1 | Spring Compresso, Side Strut, MLG | | | |
| A32033-17 | Sling, MLG | | | |
| A32034-1 | Wrench Adapter, Steering Nut, NLG | | | |
| A32035-1 | Wrench, Steering Actuator, NLG | | | |
| A32036-43 | Hoist Equipment, NLG Installation/Removal | | | |
| A32036-57 | Hoist Equipment, NLG Installation/Removal | | Replaced by A32036-66 | |
| A32036-66 | Hoist Equipment, NLG Installation/Removal | | | |
| A32038-1 | Transportation Dolly, NLG, 757 & 767 | | | |
| A32038-23 | Transportation Dolly, NLG, 757 & 767 | | | |
| A32039-1 | Removal Tool, MLG Bogie Pivot Pin | | | |
| A32040-10 | Wrench, Rod End | | | |
| A32040-12 | Wrench, Rod End | | | |
| A32040-15 | Wrench, Rod End | | | |
| A32040-4 | Wrench, Rod End | | | |
| A32040-7 | Wrench, Rod End | | | |
| A32041-1 | Torque Adapter, Cylinder, NLG Retract Actuator | | | |
| A32042-1 | Fixture, Functional Test, Side Strut Spring Assy | | | |
| A32043-1 | Test Fixture, Actuator, MLG Door Latch | | | |
| A32045-1 | Wrench - Spanner | | | |
| A32045-12 | Wrench - Spanner | | | |
| A32045-2 | Wrench - Spanner | | | |
| A32045-24 | Wrench - Spanner | | | |
| A32045-25 | Wrench - Spanner | | | |
| A32045-3 | Wrench - Spanner | | | |
| A32045-34 | Wrench - Spanner | | | |
| A32045-40 | Wrench - Spanner | | | |
| A32045-45 | Wrench - Spanner | | | |
| A32045-46 | Wrench - Spanner | | | |
| A32045-47 | Wrench - Spanner | | Replaced by A32045-87 | |
| A32045-48 | Wrench - Spanner | | | |
| A32045-50 | Wrench - Spanner | | Replaced by A32045-91 | |
| A32045-53 | Wrench - Spanner | | | |
| A32045-57 | Wrench - Spanner | | | |
| A32045-58 | Wrench - Spanner | | | |
| A32045-65 | Wrench - Spanner | | | |
| A32045-66 | Wrench - Spanner | | | |
| A32045-69 | Wrench - Spanner | | Replaced by A32045-79 | |
| A32045-70 | Wrench - Spanner | | | |
| A32045-75 | Wrench - Spanner | | | |
| A32045-76 | Wrench - Spanner | | | |
| A32045-77 | Wrench - Spanner | | | |
| A32045-78 | Wrench - Spanner | | | |
| A32045-79 | Wrench - Spanner | | | |
| A32045-8 | Wrench - Spanner | | | |
| A32045-80 | Wrench - Spanner | | Replaced by A32045-88 | |
| A32045-87 | Wrench - Spanner | | | |
| A32045-88 | Wrench - Spanner | | | |
| A32045-90 | Wrench - Spanner | | | |
| A32045-91 | Wrench - Spanner | | | |
| A32046-14 | Fishpole Hoist Attach Bracket, MLG Door | | Replaced by A32046-17 | |
| A32046-17 | Fishpole Hoist Attach Bracket, MLG Door | | | |
| A32047-1 | Component Maintenance equipment, Shock Strut, NLG | | | |
| A32047-29 | Component Maintenance equipment, Shock Strut, NLG | | | |
| A32050-1 | Torque Fixture, Actuator Piston, MLG and NLG | | | |
| A32051-1 | Component Maintenance equipment, Shock Strut, MLG | | | |
| A32052-1 | Test Fitting, Actuator, NLG Steering | | | |
| A32053-1 | Spanner Wrench, Retaining Nut, Steering Actuator | | | |
| A32054-1 | Pin, Alignment, Truck Axle Beam, MLG | | | |
| A32055-1 | Locating Jig, Sequence Valve, MLG Operated | | | |
| A32056-1 | Stand Equipment, MLG Buildup | | Replaced by B32050-50 | |
| A32057-1 | Buildup Stand, NLG | | | |
| A32057-40 | Buildup Stand, NLG | | | |
| A32058-1 | Holding Fixture, Actuator Lock, NLG | | | |
| A32059-1 | Holding Equipment, Actuator, MLG Door | | Replaced by A32059-13 | |
| A32059-13 | Holding Equipment, Actuator, MLG Door | | | |
| A32059-14 | Holding Equipment, Actuator, MLG Door | | Replaced by A32059-27 | |
| A32059-15 | Holding Equipment, Actuator, MLG Door | | Replaced by A32059-27 | |
| A32059-27 | Holding Equipment, Actuator, MLG Door | | | |
| A32060-1 | Test Fixture, Actuator, Wheel Brake | | | |
| A32061-1 | Backlash Check Equipment, NLG Steering Gearbox | | | |
| A32062-1 | Guide, Pivot Pin, MLG | | | |
| A32063-1 | Test Fixture, Side & Drag Brace Lock Actuator MLG | | Replaced by A32063-7 | |
| A32063-7 | Test Fixture, Side & Drag Brace Lock Actuator MLG | | | |
| A32064-1 | Fixture, Test, MLG Door Arming Lockout Actuator | | | |
| A32065-1 | Restraining Wrench, MLG & Retract Act. Support Pin | | | |
| A32066-1 | Drain Equipment - Shock Strut, MLG/NLG | | Replaced by J32060-1 | |
| A32067-1 | Puller Equipment, Bushing, MLG Bogie Beam | | Replaced by A32067-11 | |
| A32067-11 | Puller Equipment, Bushing, MLG Bogie Beam | | | |
| A32067-13 | Puller Equipment, Bushing, MLG Bogie Beam | | | |
| A32068-1 | Test stand, Truck Positioner, MLG | | Replaced by A32068-7 | |
| A32068-1 | Test stand, Truck Positioner, MLG | | Replaced by A32119-1 | |
| A32068-7 | Test stand, Truck Positioner, MLG | | Replaced by A32119-1 | |
| A32069-1 | Wrench Adapter, Retaining Nut, Anti-Skid Transducr | | Replaced by A32069-7 | |
| A32069-7 | Wrench Adapter, Retaining Nut, Anti-Skid Transducr | | | |
| A32070-1 | Torque Adapter, Snubber Nut | | | |
| A32071-1 | Compression Tool, Spring Cart. Nose Wheel Steering | | | |
| A32072-1 | Fixture, Functional Test, NLG Steering Actuator | | | |
| A32073-1 | Rigging Bar, Main Gear Side Strut | | | |
| A32074-1 | Breakout Box, Relay System, Air/Ground | | | |
| A32075-1 | Adapter, Anti-Skid Transducer, Spin-up | | Replaced by A32075-10 | |
| A32075-10 | Adapter, Anti-Skid Transducer, Spin-up | | | |
| A32075-9 | Adapter, Anti-Skid Transducer, Spin-up | | Replaced by A32075-10 | |
| A32076-1 | Clamp Eqmnt, Piston Rod, MLG Truck Positioner Assy | | Replaced by A32076-5 | |
| A32076-5 | Clamp Eqmnt, Piston Rod, MLG Truck Positioner Assy | | | |
| A32077-1 | Gauge, MLG Door, Open Position | | | |
| A32078-1 | Adapter Set, Retaining Nut, Act. Side & Drag Brace | | | |
| A32079-1 | Puller Equipment, Brake Sleeve, MLG Axle | | | |
| A32080-1 | Brake Disconnect, Flight Dispatch | | | |
| A32081-1 | Plug, Bushing Installation, MLG Bogie | | | |
| A32083-1 | Axle Puller, MLG | | Replaced by A32083-12 | |
| A32083-12 | Axle Puller, MLG | | | |
| A32084-1 | Holding Fixture, Piston Rod, NLG Lock Actuator | | | |
| A32086-1 | Jig Downlock Stop Shim Adjustment | | | |
| A32087-1 | Fixture Holding, MLG Retract Actuator | | | |
| A32088-1 | Maintence Lock, Retractable Tail Skid | | Replaced by A32088-7 | |
| A32088-7 | Maintence Lock, Retractable Tail Skid | | | |
| A32089-1 | Swaging Fixture, Piston Rod, MLG | | | |
| A32090-10 | Hoist Equipment, Tail Skid Shock Strut | | Replaced by A32027-175 | |
| A32090-10 | Hoist Equipment, Tail Skid Shock Strut | | Replaced by A32090-14 | |
| A32090-14 | Hoist Equipment, Tail Skid Shock Strut | | | |
| A32091 | Hole Saw | | | |
| A32092-1 | Gage Equipment, Rigging, Brake Quadrant, MLG | | | |
| A32094-1 | Gauge, Down Lock Link Adjustment, NLG | | | |
| A32095-1 | Wrench, Bearing Retaining Bolt, MLG | | | |
| A32096-10 | Rigging Equipment, Landing Gear, Air/Ground Sensor | | Replaced by A32096-70 | |
| A32096-70 | Rigging Equipment, Landing Gear, Air/Ground Sensor | | | |
| A32096-86 | Rigging Equipment, Landing Gear, Air/Ground Sensor | | | |
| A32097-1 | Protector Equipment, Externally Threaded Axle, NLG | | | |
| A32098-1 | Protector Equipment, Axle, MLG | | | |
| A32098-12 | Protector Equipment, Axle, MLG | | | |
| A32099-25 | Spring Extender Equipment | | Replaced by A32099-78 | |
| A32099-38 | Spring Extender Equipment | | | |
| A32099-38 | Spring Extender Equipment | | Replaced by A32099-78 | |
| A32099-77 | Spring Extender Equipment | | | |
| A32099-78 | Spring Extender Equipment | | | |
| A32100-1 | Installation Equipment, Brake Sleeve, MLG | | | |
| A32101-1 | Wrench Adapter, Axle Nut, NLG | | | |
| A32102-1 | Actuator Set, Proximity Sensor | | | |
| A32102-13 | Actuator Set, Proximity Sensor | | Replaced by A32102-25 | |
| A32102-25 | Actuator Set, Proximity Sensor | | | |
| A32103-1 | Lockout Pin, FWD/AFT Lock Link, Retract Tail Skid | | | |
| A32104-1 | Puller Equipment, Fuse Pin, Forward Trunnion, MLG | | | |
| A32105-1 | Sling Equipment, Drag & Side Strut Rem/Inst MLG | | | |
| A32106-1 | Shock Trut Equipment, Component Maintenance, MLG | | | |
| A32107-1 | Replacement equipment, Lower Bearing Seals, MLG | | | |
| A32108-1 | Sling Equipment, Retract Actuator, MLG | | | |
| A32108-2 | Sling Equipment, Retract Actuator, MLG | | | |
| A32109-1 | Pin Installation/Removal Kit, MLG | | Replaced by A32109-41 | |
| A32109-41 | Pin Installation/Removal Kit, MLG | | | |
| A32110-1 | Pin Puller Equipment, Brake Rod, MLG | | | |
| A32111-1 | Rigging Tube Equipment, Side Strut, MLG | | | |
| A32112-1 | Removal/Install Guide Equipment, Aft Trunnion, MLG | | | |
| A32113-1 | Pin Puller Equipment, Retract Actautor, MLG | | | |
| A32114-1 | Truck Position Retainer & Oleo Lock Equipment, MLG | | Replaced by A32114-64 | |
| A32114-64 | Truck Position Retainer & Oleo Lock Equipment, MLG | | | |
| A32115-1 | Overhead Installation/Removal Equipment, MLG | | | |
| A32115-2 | Overhead Installation/Removal Equipment, MLG | | | |
| A32115-6 | Overhead Installation/Removal Equipment, MLG | | | |
| A32116-1 | Removal Equipment, MLG Bogie Pivot Pin | | | |
| A32117-1 | Locating Jig, Sequence Valve, MLG Operated | | | |
| A32118-1 | Fishpole Hoist Attach Bracket Equipment, MLG Door | | | |
| A32119-1 | Test Stand assembly, Truck Positioner, MLG | | | |
| A32120-1 | Torque Adapter Set, Actuator Components, MLG | | | |
| A32121-1 | Fixture Equipment, Landing Gear Actuator Assembly | | | |
| A32122-1 | Fixture Equipment, Retract Actuator, MLG | | | |
| A32123-1 | Rigging Assembly, Air/Ground Sensor, Right Hnd MLG | | | |
| A33001-1 | Test Box, Master Dim & Test PC Card | | | |
| A33003-1 | Breakout Box, Multipurpose | | Replaced by A33003-359 | |
| A33003-359 | Breakout Box, Multipurpose | | | |
| A33004-1 | Test Box, Autobright Sensor | | Replaced by A33004-32 | |
| A33004-32 | Test Box, Autobright Sensor | | | |
| A34001-1 | Warning Eqpmnt, ATC, DME, VHF Antenna & Drain Mast | | Replaced by A34001-4 | |
| A34001-4 | Warning Eqpmnt, ATC, DME, VHF Antenna & Drain Mast | | | |
| A34003-1 | Test Box, Rear Module & Control Panel, ATC | | Replaced by A34003-43 | |
| A34003-43 | Test Box, Rear Module & Control Panel, ATC | | Replaced by A34003-46 | |
| A34003-46 | Test Box, Rear Module & Control Panel, ATC | | | |
| A34004-24 | Test Box, Front Module, ATC | | Replaced by A34004-27 | |
| A34004-27 | Test Box, Front Module, ATC | | Replaced by A34004-30 | |
| A34004-30 | Test Box, Front Module, ATC | | | |
| A34005-1 | Test Box, ADF Front Module Assy | | | |
| A34006-1 | Test Box, ADF Control Panel & Rear Module | | Replaced by A34006-21 | |
| A34006-21 | Test Box, ADF Control Panel & Rear Module | | | |
| A34007-33 | Test box, Rear Module & Control Panel, ILS | | Replaced by A34007-36 | |
| A34007-36 | Test box, Rear Module & Control Panel, ILS | | | |
| A34008-1 | Test Box, Front Module, ILS | | | |
| A34009-26 | Test Box, Rear Module & Control Panel | | Replaced by A34009-29 | |
| A34009-29 | Test Box, Rear Module & Control Panel | | | |
| A34010-1 | Test Box, Front Module | | | |
| A34010-21 | Test Box, Front Module | | | |
| A34011-1 | Breakout Box Equipment, Arinc600, Line Maintenance | | Replaced by A34016-1 | |
| A34011-112 | Breakout Box Equipment, Arinc600, Line Maintenance | | Replaced by A34016-1 | |
| A34011-119 | Breakout Box Equipment, Arinc600, Line Maintenance | | Replaced by A34011-165 | |
| A34011-165 | Breakout Box Equipment, Arinc600, Line Maintenance | | | |
| A34012-1 | Test Fixture, Angle of Attack | | Replaced by A34012-24 | |
| A34012-19 | Test Fixture, Angle of Attack | | | |
| A34012-24 | Test Fixture, Angle of Attack | | | |
| A34013-1 | Test Box, Power Supply Control Panel | | Replaced by A34013-18 | |
| A34013-18 | Test Box, Power Supply Control Panel | | | |
| A34014-1 | Test Box, Power Supply Control Panel | | Replaced by A34014-14 | |
| A34014-14 | Test Box, Power Supply Control Panel | | | |
| A34015-1 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-26 | |
| A34015-10 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-26 | |
| A34015-13 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-26 | |
| A34015-16 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-26 | |
| A34015-20 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-26 | |
| A34015-23 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-27 | |
| A34015-26 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-35 | |
| A34015-27 | Test Box, Power Interrupt/Pulse | | Replaced by A34015-35 | |
| A34015-35 | Test Box, Power Interrupt/Pulse | | | |
| A34016-1 | Breakout Box Equipment, ARINC 600, Line Maint. | | | |
| A35001-1 | Retraction Equipment, Firing Pin, Oxygen System | | Replaced by A35001-10 | |
| A35001-10 | Retraction Equipment, Firing Pin, Oxygen System | | Replaced by C35003-1 | |
| A35002-1 | Door Retainer, Passenger Support Unit Oxygen | | Replaced by A35002-7 | |
| A35002-10 | Door Retainer, Passenger Support Unit Oxygen | | | |
| A35002-7 | Door Retainer, Passenger Support Unit Oxygen | | Replaced by A35002-10 | |
| A36001-1 | Removal/Installation Equipment, Engine Precooler | | Replaced by A36001-45 | |
| A36001-24 | Removal/Installation Equipment, Engine Precooler | | Replaced by A36001-44 | |
| A36001-44 | Removal/Installation Equipment, Engine Precooler | | | |
| A36001-45 | Removal/Installation Equipment, Engine Precooler | | | |
| A36003-135 | Cap, Pneumatic Ducts Hydrostatic Pressure Tst | | Replaced by A36003-175 | |
| A36003-173 | Plug Set, Pneumatic Ducts Hydrostatic Pressure Tst | | | |
| A36003-175 | Cap, Pnematic Ducts Hydraustatic Pressure Test | | | |
| A36004-1 | Installation Equipment, CF6-80C2B, Ball Joint | | Replaced by A36004-15 | |
| A36004-15 | Installation Equipment, CF6-80C2B, Ball Joint | | | |
| A36005-1 | Hold Open Equipment, PRSOV | | Replaced by A36005-15 | |
| A36005-15 | Hold Open Equipment, PRSOV | | | |
| A36006-1 | Dummy Check Valve, IP Pneumatic System, Disptch Eq | | | |
| A36007-1 | Test Equipment, IP Dummy Check Valve | | | |
| A36008-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36009-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36010-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36011-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36012-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36013-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36014-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36015-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36016-1 | Pressure Test Equipment, Duct Assembly | | | |
| A36017-1 | Plug, Duct, Proof Pressure Test | | | |
| A36018-1 | Plug Equipment, Duct, Proof Pressure Test | | | |
| A36019-1 | Plug Equipment, Duct, Proof Pressure Test | | | |
| A36020-1 | Plug Equipment, Duct, Proof Pressure Test | | | |
| A36021-1 | Adapter Cable, BITE Module, Air Supply System | | | |
| A36022-1 | Removal/Installation Equipment, RB211 Precooler | | | |
| A38001-1 | Plugs, Vent, Vacuum Waste System | | Replaced by A38001-16 | |
| A38001-16 | Plugs, Vent, Vacuum Waste System | | Replaced by A38001-22 | |
| A38001-22 | Plugs, Vent, Vacuum Waste System | | | |
| A38002-1 | Test Box, Signal Unit PCA Potable Water | | | |
| A38003-1 | Blockage Remover, Vacuum Toilet | | Replaced by A38003-14 | |
| A38003-14 | Blockage Remover, Vacuum Toilet | | | |
| A38003-20 | Blockage Remover, Vacuum Toilet | | | |
| A38004-15 | Cleaner Equipment, Waste Tank Sensors | | Replaced by A38004-29 | |
| A38004-15 | Cleaner Equipment, Waste Tank Sensors | | Replaced by A38009-11 | |
| A38004-29 | Cleaner Equipment, Waste Tank Sensors | | Replaced by A38009-11 | |
| A38005-1 | Rooter, Waste Water Drain Line | | | |
| A38006-1 | Tester, Toilet Vacuum | | | |
| A38007-1 | Plug, Vacuum Waste System | | | |
| A38008-1 | Blockage Remover, Vacuum Toilet | | Replaced by A38003-14 | |
| A38009-1 | Sensor Cleaner, Lavatory Waste Tank | | Replaced by A38009-11 | |
| A38009-11 | Sensor Cleaner, Lavatory Waste Tank | | | |
| A38010-1 | Test Cable, Potable Water Quantity Transmitter | | Replaced by A38010-11 | |
| A38010-11 | Test Cable, Potable Water Quantity Transmitter | | | |
| A38011-1 | Plug Equipment, Drain Mast, Waste Water | | Replaced by C38001-23 | |
| A38012-1 | Pump Equipment, Vacuum Lavatory System | | Replaced by A38012-31 | |
| A38012-18 | Pump Equipment, Vacuum Lavatory System | | Replaced by A38012-32 | |
| A38012-31 | Pump Equipment, Vacuum Lavatory System | | Replaced by A38012-39 | |
| A38012-32 | Pump Equipment, Vacuum Lavatory System | | Replaced by A38012-40 | |
| A38012-39 | Pump Equipment, Vacuum Lavatory System | | | |
| A38012-40 | Pump Equipment, Vacuum Lavatory System | | | |
| A38014-1 | Dor witch Actuator, Potable Water Service Panel | | | |
| A49001-17 | Cradle, Auxiliary Power Unit | | | |
| A49001-3 | Cradle, Auxiliary Power Unit | | | |
| A49001-73 | Cradle, Auxiliary Power Unit | | Replaced by A49001-83 | |
| A49001-74 | Cradle, Auxiliary Power Unit | | | |
| A49001-77 | Cradle, Auxiliary Power Unit | | Replaced by A49001-78 | |
| A49001-78 | Cradle, Auxiliary Power Unit | | Replaced by A49001-84 | |
| A49001-83 | Cradle, Auxiliary Power Unit | | | |
| A49001-84 | Cradle, Auxiliary Power Unit | | | |
| A49002-1 | Lifting Eye - APU Generator | | | |
| A49002-2 | Lifting Eye - APU Generator | | | |
| A49003-1 | Transportation Dolly, APU | | Replaced by A49003-12 | |
| A49003-12 | Transportation Dolly, APU | | | |
| A49004-1 | Support Equipment, APU | | | |
| A49005-1 | Sling, APU Shop Handling | | Replaced by A49005-12 | |
| A49005-12 | Sling, APU Shop Handling | | | |
| A49006-26 | Hoist Equipment - APU Battery | | Replaced by A24006-1 | |
| A49009-1 | Kit, APU Deactivation | | | |
| A51001-1 | Service Platform Forward of the APU Door | | Replaced by A51001-19 | |
| A51001-19 | Service Platform Forward of the APU Door | | | |
| A51002-1 | Alignment Equipment, Airplane Structural Repair | | | |
| A51003-1 | Ladder Set, Empennage, Pressure Bulkhead | | Replaced by A51004-1 | |
| A51004-1 | Ladder Set, Empennage, Pressure Bulkhead | | | |
| A51005-1 | Oil Can Cage, Pressure Bulkhead | | Replaced by A51005-14 | |
| A51005-14 | Oil Can Cage, Pressure Bulkhead | | | |
| A51006-21 | Measurement Equipment, Check, Skin Smoothness | | Replaced by A51006-26 | |
| A51006-26 | Measurement Equipment, Check, Skin Smoothness | | | |
| A51007-1 | Maintenance Platform Eqmnt, Press Bulkhead Access | | | |
| A52002-1 | Safety Barrier, Entry, Mid-Entry or Service Door | | Replaced by A52002-13 | |
| A52002-13 | Safety Barrier, Entry, Mid-Entry or Service Door | | | |
| A52003-1 | Lock, Counterbalance, Entry & Service Doors | | | |
| A52004-1 | Sling Equipment, Door Handling | | Replaced by A52004-41 | |
| A52004-1 | Sling Equipment, Door Handling | | Replaced by A52004-43 | |
| A52004-10 | Sling Equipment, Door Handling | | Replaced by A52004-42 | |
| A52004-17 | Sling Equipment, Door Handling | | Replaced by A52004-43 | |
| A52004-40 | Sling Equipment, Door Handling | | Replaced by A52004-41 | |
| A52004-41 | Sling Equipment, Door Handling | | | |
| A52004-42 | Sling Equipment, Door Handling | | | |
| A52004-43 | Sling Equipment, Door Handling | | | |
| A52005-1 | Safety Barrier, Cargo Door, Forward/Aft | | | |
| A52006-1 | Replacement Equipment, Bulk Cargo Door | | | |
| A52007-1 | Safety Barrier, Forward Large Cargo Door | | | |
| A52008-10 | Ground Lock, Entry/Service Door | | Replaced by A52008-14 | |
| A52008-14 | Ground Lock, Entry/Service Door | | | |
| A52009-1 | Test Fixture, Bungee Spring, Cargo Door | | Replaced by A52009-22 | |
| A52009-22 | Test Fixture, Bungee Spring, Cargo Door | | | |
| A52010-14 | Clamp Equipment, Spring Inst/Rem, Bulk Cargo Door | | Replaced by A52010-50 | |
| A52010-15 | Clamp Equipment, Spring Inst/Rem, Bulk Cargo Door | | Replaced by A52010-51 | |
| A52010-50 | Clamp Equipment, Spring Inst/Rem, Bulk Cargo Door | | | |
| A52010-51 | Clamp Equipment, Spring Inst/Rem, Bulk Cargo Door | | | |
| A52013-1 | Dummy Weigth Slide Pack, Passenger & Service Door | | Replaced by A52013-31 | |
| A52013-31 | Dummy Weigth Slide Pack, Passenger & Service Door | | | |
| A52014-1 | Adjustment Set, Main Latch Pin, Large Cargo Doors | | | |
| A52015-1 | Shaft Support, Counterbalance, Overhead Pass Door | | Replaced by A52015-3 | |
| A52015-3 | Shaft Support, Counterbalance, Overhead Pass Door | | | |
| A52016-1 | igging Adjustment Equipment, FWD & AFT Cargo Doors | | | |
| A52017-1 | Test Fixture, Gearbox, Overhead Pass Door Cntrblnc | | | |
| A52018-1 | Test Equipment, Large Cargo Door Latch Lock | | Replaced by A52018-15 | |
| A52018-15 | Test Equipment, Large Cargo Door Latch Lock | | | |
| A52019-1 | Driver Set, Hinge Pin, Large Cargo Door | | | |
| A52020-1 | Mandrel Equipment, Bearing Installation | | | |
| A52021-1 | Wrench, Proximity Sensor, Bulk Cargo Door | | | |
| A52022-1 | Canopy, FWD Entry Door | | | |
| A52023-1 | Backlash Check Eqmnt, Manual Drive, Lrg Cargo Door | | | |
| A52025-1 | Service Platform, Service Access Door | | | |
| A52027-1 | Saftey Barrier, AFT Emergency Exit | | | |
| A52028-1 | Verification Eqmt, Main Latch Fittings, Cargo Door | | | |
| A52029-1 | Gage, Girt bar, carrier Drive | | | |
| A52030-1 | Staking Equipment, Girt Bar Bearing | | | |
| A52031-1 | Rigging Equipment, Main Deck Cargo Door | | | |
| A52032-1 | Adjustment Tool Set, Latch Pins, Main Deck Carg Dr | | Replaced by A52032-17 | |
| A52032-17 | Adjustment Tool Set, Latch Pins, Main Deck Carg Dr | | | |
| A52033-1 | Verification Eqmt, Main Latch Fittings, Cargo Door | | | |
| A52034-1 | Rigging Equipment, Rotary Actuator, Cargo Door | | | |
| A52035-1 | Driver Equipment, Interm. Hinge Pins, Cargo Door | | | |
| A52036-1 | Sling Equipment, Main Deck Cargo Door | | | |
| A52037-1 | Test Box, Flight Deck Access System (FDAS) | | | |
| A53001-14 | Sling Radome | | | |
| A53002-1 | Safety Barrier, E/E Access Hatch | | Replaced by A53002-5 | |
| A53002-5 | Safety Barrier, E/E Access Hatch | | | |
| A54001-136 | Sling Equipment, Strut Unload, Pin Removal/Install | | Replaced by A54001-165 | |
| A54001-137 | Sling Equipment, Strut Unload, Pin Removal/Install | | Replaced by A54001-167 | |
| A54001-157 | Sling Equipment, Strut Unload, Pin Removal/Install | | Replaced by A54001-168 | |
| A54001-165 | Sling Equipment, Strut Unload, Pin Removal/Install | | Replaced by A54001-168 | |
| A54001-167 | Sling Equipment, Strut Unload, Pin Removal/Install | | | |
| A54001-168 | Sling Equipment, Strut Unload, Pin Removal/Install | | | |
| A54002-1 | Drill Jig, Side Link, Nacelle Strut | | Replaced by A54002-9 | |
| A54002-9 | Drill Jig, Side Link, Nacelle Strut | | | |
| A54003-1 | Sling Equipment, Strut Removal/Installation | | | |
| A54003-2 | Sling Equipment, Strut Removal/Installation | | Replaced by A54003-41 | |
| A54003-3 | Sling Equipment, Strut Removal/Installation | | Replaced by A54003-42 | |
| A54003-41 | Sling Equipment, Strut Removal/Installation | | | |
| A54003-42 | Sling Equipment, Strut Removal/Installation | | | |
| A54003-51 | Sling Equipment, Strut Removal/Installation | | | |
| A54004-19 | Preload Equipment, Strut Installation | | Replaced by A54004-27 | |
| A54004-27 | Preload Equipment, Strut Installation | | | |
| A54005-1 | Sling Equipment, Strut, RB211-524H | | Replaced by A54012-1 | |
| A54007-1 | Sling, Diagonal Brace Unload, RB211-524 Engine | | Replaced by A54007-15 | |
| A54007-15 | Sling, Diagonal Brace Unload, RB211-524 Engine | | | |
| A54008-1 | Puller equipment, Fuse Pin | | Replaced by A54011-13 | |
| A54008-13 | Puller equipment, Fuse Pin | | | |
| A54009-1 | Proofload Fixture, RB211-524H Strut Sling | | | |
| A54011-13 | Removal/Installation Kit, Midspar Fuse Pin | | Replaced by A54011-18 | |
| A54011-18 | Removal/Installation Kit, Midspar Fuse Pin | | | |
| A54011-24 | Removal/Installation Kit, Midspar Fuse Pin | | | |
| A54011-25 | Removal/Installation Kit, Midspar Fuse Pin | | | |
| A54011-26 | Removal/Installation Kit, Midspar Fuse Pin | | | |
| A54012-1 | Sling Equipment, Strut, RB211-524H | | | |
| A55001-1 | Lock Equipment, Horizontal Stabilizer | | Replaced by A55001-19 | |
| A55001-19 | Lock Equipment, Horizontal Stabilizer | | Replaced by A55001-22 | |
| A55001-22 | Lock Equipment, Horizontal Stabilizer | | | |
| A55001-42 | Lock Equipment, Horizontal Stabilizer | | Replaced by A55001-47 | |
| A55001-47 | Lock Equipment, Horizontal Stabilizer | | | |
| A55003-1 | Alignment Equipment, Hinge, Inboard Elevator | | | |
| A55004-95 | Jacking Equipment, Hinge, Horizontal Stabilizer | | Replaced by A55004-98 | |
| A55004-98 | Jacking Equipment, Hinge, Horizontal Stabilizer | | | |
| A55005-1 | Removal Equipment, Pivot Brg, Horizontal Stabilizr | | | |
| A55006-1 | Template, Blade Seal Fitting, Horizontal Stabilizr | | | |
| A55007-1 | Rem/Inst Equipment, Pivot Brg Horizontal Stabilizr | | Replaced by A27114-1 | |
| A56001-1 | Sling Set, Number 1 & 3 Cockpit Window | | Replaced by A56001-15 | |
| A56001-15 | Sling Set, Number 1 & 3 Cockpit Window | | | |
| A56004-50 | Repair Set, Number 2 Window | | | |
| A56004-60 | Repair Set, Number 2 Window | | Replaced by A56004-50 | |
| A57001-1 | Jig Equipment, Reaming, Trunnion Support, MLG | | | |
| A57002-1 | Replacement Equipment, Outboard TE Flap | | | |
| A57003-1 | Locating Eqmnt, Wedge Replmnt, Inbd/Outbd LE Slat | | | |
| A57004-1 | Sling, Raked Wing Tip, Installation and Removal | | | |
| A57005-1 | Socket Assembly, Retention Nut, MLG Act Supp, Wing | | | |
| A57006-1 | Spanner Wrench, Special Nut, Inbd TE Main Flap | | | |
| A57007-1 | Lubricating Eqmnt, LE Slat Aux Arm Roller Bolt | | Replaced by A57007-8 | |
| A57007-8 | Lubricating Eqmnt, LE Slat Aux Arm Roller Bolt | | | |
| A57008-1 | Removal/Installation Equipment, MLG Bottle Pin | | | |
| A71001-182 | Bootstrap Equipment Pratt & Whitney Engines | | Replaced by A71001-185 | |
| A71001-185 | Bootstrap Equipment Pratt & Whitney Engines | | Replaced by A71001-191 | |
| A71001-191 | Bootstrap Equipment Pratt & Whitney Engines | | | |
| A71002-48 | Sling Equipment, Thrust Reverser | | Replaced by A71002-50 | |
| A71002-50 | Sling Equipment, Thrust Reverser | | | |
| A71003-25 | Torque Equipment, Engine Mounts, JT9D-7R4D/PW4000 | | Replaced by A71003-53 | |
| A71003-26 | Torque Equipment, Engine Mounts, JT9D-7R4D/PW4000 | | Replaced by A71003-41 | |
| A71003-41 | Torque Equipment, Engine Mounts, JT9D-7R4D/PW4000 | | Replaced by A71003-54 | |
| A71003-53 | Torque Equipment, Engine Mounts, JT9D-7R4D/PW4000 | | | |
| A71003-54 | Torque Equipment, Engine Mounts, JT9D-7R4D/PW4000 | | | |
| A71005-25 | Sling Equipment, Engine Inlet Cowl | | Replaced by A71005-33 | |
| A71005-31 | Sling Equipment, Engine Inlet Cowl | | Replaced by A71005-33 | |
| A71005-33 | Sling Equipment, Engine Inlet Cowl | | | |
| A71006-76 | Cradle, Pratt & Whitney Engines, 90-inch Rail | | Replaced by A71006-79 | |
| A71006-79 | Cradle, Pratt & Whitney Engines, 90-inch Rail | | | |
| A71007-23 | Proof Load Fixture, Bootstrap, JT9D7R4 & PW4000 | | Replaced by A71007-27 | |
| A71007-27 | Proof Load Fixture, Bootstrap, JT9D7R4 & PW4000 | | | |
| A71007-27 | Proof Load Fixture, Bootstrap, JT9D7R4 & PW4000 | | Replaced by A71007-39 | |
| A71007-39 | Proof Load Fixture, Bootstrap, JT9D7R4 & PW4000 | | | |
| A71008-1 | Sling Equipment, Pratt & Whitney Engine | | Replaced by A71008-64 | |
| A71008-64 | Sling Equipment, Pratt & Whitney Engine | | | |
| A71008-65 | Sling Equipment, Pratt & Whitney Engine | | | |
| A71009-25 | Sling, Thrust Reverser CF6-80A | | Replaced by A71009-26 | |
| A71009-26 | Sling, Thrust Reverser CF6-80A | | | |
| A71011-242 | Bootstrap Equipment, GE Engine | | Replaced by A71011-262 | |
| A71011-243 | Bootstrap Equipment, GE Engine | | Replaced by A71011-263 | |
| A71011-262 | Bootstrap Equipment, GE Engine | | | |
| A71011-263 | Bootstrap Equipment, GE Engine | | | |
| A71012-1 | Proof Load Equipment, Craddle, P&W | | Replaced by A71012-35 | |
| A71012-35 | Proof Load Equipment, Craddle, P&W | | | |
| A71013-19 | Hoist Adapter, IDG | | | |
| A71013-32 | Hoist Adapter, IDG | | | |
| A71013-40 | Hoist Adapter, IDG | | | |
| A71013-45 | Hoist Adapter, IDG | | | |
| A71013-55 | Hoist Adapter, IDG | | Replaced by A71013-82 | |
| A71013-70 | Hoist Adapter, IDG | | Replaced by A71013-82 | |
| A71013-82 | Hoist Adapter, IDG | | | |
| A71013-88 | Hoist Adapter, IDG | | | |
| A71015-107 | Lift Fixture - Engine Accessory | | | |
| A71015-87 | Lift Fixture - Engine Accessory | | Replaced by A71015-93 | |
| A71015-93 | Lift Fixture - Engine Accessory | | Replaced by A71015-107 | |
| A71016-1 | Sling Equipment, Core Cowl | | | |
| A71017-1 | Lift Sling, Core Cowl | | | |
| A71019-60 | Engine Handling equipment, CF6-80A | | | |
| A71020-1 | Proof Load Fixture, Cradle CF6-80A | | | |
| A71021-36 | Proof Load Fixture, Bootstrap, GE Engines | | Replaced by A71021-52 | |
| A71021-52 | Proof Load Fixture, Bootstrap, GE Engines | | | |
| A71022-1 | Locating Jig, Engine Build-up to Strut Syst. JT9D | | | |
| A71022-60 | Locating Jig, Engine Build-up to Strut Syst. JT9D | | | |
| A71023-1 | Cradle, CF6-80A Engine 90 inch Rail | | Replaced by A71023-53 | |
| A71023-53 | Cradle, CF6-80A Engine 90 inch Rail | | | |
| A71024-1 | Locating Jig, CF6-80A Build-up Strut Sys Interface | | Replaced by A71024-68 | |
| A71024-51 | Locating Jig, CF6-80A Build-up Strut Sys Interface | | Replaced by A71024-70 | |
| A71024-68 | Locating Jig, CF6-80A Build-up Strut Sys Interface | | | |
| A71024-70 | Locating Jig, CF6-80A Build-up Strut Sys Interface | | | |
| A71025-1 | Support Pedestal Equipment, CF6-80A Engine Buildup | | | |
| A71026-1 | Hold Open equipment, Fan Cowl, CF6-80A | | | |
| A71026-23 | Sling Euipment, Core Cowl | | | |
| A71027-1 | Hold Open Equipment, Fan Cowl, CF6-80A | | | |
| A71029-1 | Hold Open Equipment, Fan Cowl, JT9D-7R4 Engine | | | |
| A71029-36 | Hold Open Equipment, Fan Cowl, JT9D-7R4 Engine | | Replaced by A71029-1 | |
| A71030-1 | Hold Open Equipment, Fan Cowl, P&W Engines | | | |
| A71030-32 | Hold Open Equipment, Fan Cowl, P&W Engines | | | |
| A71032-1 | Hold-Open Equipment, P&W Core Cowls | | Replaced by A71032-14 | |
| A71032-14 | Hold-Open Equipment, P&W Core Cowls | | | |
| A71033-1 | Hold Open Equipment, Core Cowl, CF6-80A | | Replaced by A71033-19 | |
| A71033-19 | Hold Open Equipment, Core Cowl, CF6-80A | | Replaced by A71033-31 | |
| A71033-31 | Hold Open Equipment, Core Cowl, CF6-80A | | | |
| A71034-1 | Wrench, Aft Flight Mount EBU B Package | | | |
| A71034-2 | Wrench, Aft Flight Mount EBU B Package | | Replaced by A71034-3 | |
| A71034-3 | Wrench, Aft Flight Mount EBU B Package | | | |
| A71035-1 | Cover Equipment, Bleed Valve GE Engine | | | |
| A71035-13 | Cover Equipment, Bleed Valve GE Engine | | Replaced by A71035-27 | |
| A71035-27 | Cover Equipment, Bleed Valve GE Engine | | | |
| A71036-1 | Monitoring ssembly, Breather Pressure, JT9D-7R4 | | | |
| A71037-1 | Test Eqpmnt, Drying & Leak Check, JT9D-7R4D Gearbx | | | |
| A71038-1 | Alignment Handle, Forward Engine Mount | | | |
| A71040 | Flush Cart, Engine IDG Cooling System | | | |
| A71042-1 | Guard, Inlet, Engine Run-Up | | Replaced by A71042-29 | |
| A71042-29 | Guard, Inlet, Engine Run-Up | | | |
| A71045-1 | Storage Stand, Spare Engine Carriage | | | |
| A71046-1 | Locating Jig, Engine Buildup to Strut, PW4000 | | | |
| A71047-142 | Bootstrap Equipment, RB211-524H | | Replaced by A71047-150 | |
| A71047-150 | Bootstrap Equipment, RB211-524H | | | |
| A71048-1 | Proof Load Fixture, Bootstrap, RB211 | | | |
| A71049-1 | PT2 Probe Adapter | | | |
| A71050-1 | Hold Open Bracket, JT9D Engine | | | |
| A71051-1 | Transport & Store Pallet, Inlet Cowl, CF6-80C2B | | | |
| A71054-1 | Torque Equipment, Engine Mount Bolts, RB211-524G/H | | | |
| A76001-1 | Test Fixture, Thrust Lever, Control Stand | | | |
| A77001-1 | Test Box, Electronic Engine Cntrl Monitor Pwr Sppl | | | |
| A77002-1 | Test Box, Display Board, Elec. Eng Control Monitor | | | |
| A77003-15 | Test equipment, Indicating System, EGT | | Replaced by A77003-18 | |
| A77003-18 | Test equipment, Indicating System, EGT | | | |
| A77004-1 | Test Box, Tachometer System | | Replaced by A77004-18 | |
| A77004-18 | Text Box, Tachometer System | | | |
| A77004-19 | Text Box, Tachometer System | | | |
| A77004-2 | Test Box, Tachometer System | | Replaced by A77004-19 | |
| A77005-24 | Test equipment, Engine N1/N2 Interface | | Replaced by A77005-59 | |
| A77005-37 | Test equipment, Engine N1/N2 Interface | | Replaced by A77005-60 | |
| A77005-52 | Test equipment, Engine N1/N2 Interface | | Replaced by A77005-61 | |
| A77005-59 | Test equipment, Engine N1/N2 Interface | | | |
| A77005-60 | Test equipment, Engine N1/N2 Interface | | | |
| A77005-61 | Test equipment, Engine N1/N2 Interface | | | |
| A78001-21 | Hold Open Equipment, Thrust Reverser, 40 Knot | | Replaced by A78001-48 | |
| A78001-22 | Hold Open Equipment, Thrust Reverser, 40 Knot | | Replaced by A78001-31 | |
| A78001-31 | Hold Open Equipment, Thrust Reverser, 40 Knot | | | |
| A78001-41 | Hold Open Equipment, Thrust Reverser, 40 Knot | | Replaced by A78001-41 | |
| A78001-48 | Hold Open Equipment, Thrust Reverser, 40 Knot | | | |
| A78002-1 | Thread Protector Eqmt, Thrust Reverser Rem/Inst | | | |
| A78002-4 | Thread Protector Eqmt, Thrust Reverser Rem/Inst | | Replaced by A78002-8 | |
| A78002-8 | Thread Protector Eqmt, Thrust Reverser Rem/Inst | | | |
| A78002-9 | Thread Protector Eqmt, Thrust Reverser Rem/Inst | | | |
| A78003-28 | Cradle, Exhaust Nozzle | | Replaced by A78003-41 | |
| A78003-38 | Cradle, Exhaust Nozzle | | Replaced by A78003-41 | |
| A78003-41 | Cradle, Exhaust Nozzle | | | |
| A78005-1 | Tension Latch Wrench Set, Fan Duct | | Replaced by A78005-5 | |
| A78005-5 | Tension Latch Wrench Set, Fan Duct | | | |
| A78007-1 | Sling, Sleeve Thrust Reverser CF6-80A | | | |
| A78008-1 | Sling, Sleeve, Thrust Reverser | | Replaced by A78008-16 | |
| A78008-16 | Sling, Sleeve, Thrust Reverser | | | |
| A78010-1 | Check Fixture, Spring Interlock Bell Crank, JT9D | | | |
| A78011-63 | Stand Support, Fan Duct Cowl and Thrust Reverser | | Replaced by A78011-69 | |
| A78011-64 | Stand Support, Fan Duct Cowl and Thrust Reverser | | Replaced by A78011-70 | |
| A78011-67 | Stand Support, Fan Duct Cowl and Thrust Reverser | | Replaced by A78011-69 | |
| A78011-68 | Stand Support, Fan Duct Cowl and Thrust Reverser | | Replaced by A78011-70 | |
| A78011-69 | Stand Support, Fan Duct Cowl and Thrust Reverser | | | |
| A78011-70 | Stand Support, Fan Duct Cowl and Thrust Reverser | | | |
| A78012-1 | Wrench, Crowfoot, Tubing Nut, Flow Cntrl, Thrust R | | | |
| A78013-1 | Sling, Exhaust Sleeve, Engine | | | |
| A78013-11 | Sling, Exhaust Sleeve, Engine | | | |
| A78013-2 | Sling, Exhaust Sleeve, Engine | | | |
| A78014-1 | Clam Shell Equipment, Track Slider, Thrust Reverse | | | |
| A78015-1 | Rework Jig, Hinge, Blocker Doors, Thrust Reverser | | | |
| A78017-1 | Sling, Fan Reverser Opening | | | |
| A78018-1 | Sling, Thrust Reverser Translating Sleeve,CF6-80C2 | | Replaced by A78018-11 | |
| A78018-11 | Sling, Thrust Reverser Translating Sleeve,CF6-80C2 | | | |
| A78019-17 | Hand Pump, Opening System, Thrust Reverser | | | |
| A78019-21 | Hand Pump, Opening System, Thrust Reverser | | Replaced by A78019-17 | |
| A78020-1 | Hoist Equipment, Rem/Inst, INA | | Replaced by A78020-66 | |
| A78020-66 | Hoist Equipment, Rem/Inst, INA | | | |
| A78021-1 | Test/Overhaul Equipment, Cowl Door Actuator | | Replaced by A78021-45 | |
| A78021-31 | Test/Overhaul Equipment, Cowl Door Actuator | | Replaced by A78021-46 | |
| A78021-45 | Test/Overhaul Equipment, Cowl Door Actuator | | Replaced by A78021-46 | |
| A78021-46 | Test/Overhaul Equipment, Cowl Door Actuator | | | |
| A78023-1 | Repair Fixture Equipment, PW4000 Engine Thrust Rev | | | |
| A78023-121 | Repair Fixture Equipment, PW4000 Engine Thrust Rev | | | |
| A78023-35 | Repair Fixture Equipment, PW4000 Engine Thrust Rev | | Replaced by A78023-89 | |
| A78023-89 | Repair Fixture Equipment, PW4000 Engine Thrust Rev | | | |
| A78024-1 | Alignment Fixture, Inner Fan Duct Wall CF6-80A | | | |
| A78025-1 | Breakout Box, Test, Thrust Reverser | | | |
| A78025-2 | Breakout Box, Test, Thrust Reverser | | Replaced by A78025-77 | |
| A78025-77 | Breakout Box, Test, Thrust Reverser | | | |
| B20004-1 | Leverage Adapter - Access Panel | | Replaced by B20004-13 | |
| B20004-13 | Leverage Adapter - Access Panel | | Replaced by B20004-16 | |
| B20004-16 | Leverage Adapter - Access Panel | | Replaced by B20004-21 | |
| B20004-21 | Leverage Adapter - Access Panel | | | |
| B21005-1 | Cleaning Want Equipment - Heat Exchanger | | Replaced by B21005-10 | |
| B21005-10 | Cleaning Want Equipment - Heat Exchanger | | | |
| B22002-1 | Breakout Box - Yaw Damper EMI Filter | | | |
| B22003-1 | Test Equipment -Autothrottle Clutch | | Replaced by B22003-39 | |
| B22003-20 | Test Equipment - Autothrottle Clutch | | Replaced by B22003-39 | |
| B22003-39 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-107 | |
| B22003-39 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-108 | |
| B22003-39 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-132 | |
| B23001-1 | Extender Board - Audio Accessory Unit Assembly | | | |
| B27018-1 | Breakout Box - FSEU/CSEU Power Supply | | Replaced by B27018-19 | |
| B27018-19 | Breakout Box - FSEU/CSEU Power Supply | | | |
| B27070-1 | Alignment Pin - Feel Actuator Piston | | | |
| B27079-19 | Test Box - Power Supply, CSEU | | | |
| B28001-18 | Adapter, Sump Drain Valve Removal/Installation | | | |
| B28004-1 | Socket, Collimator Sleeve Installation/Removal | | | |
| B28005-2 | Pressure Plug Equipment - Fuel System | | | |
| B28009-1 | Alignment equipment, Fuel Shutoff Valve | | | |
| B29001-1 | Screen Equipment, Ram Air Turbine | | Replaced by B29001-27 | |
| B29001-23 | Screen Equipment, Ram Air Turbine | | | |
| B29001-27 | Screen Equipment, Ram Air Turbine | | Replaced by B29001-42 | |
| B29001-42 | Screen Equipment, Ram Air Turbine | | Replaced by B29001-46 | |
| B29001-46 | Screen Equipment, Ram Air Turbine | | | |
| B29005-1 | Simulator - Yaw Damper Module | | Replaced by B29005-17 | |
| B29005-17 | Simulator - Yaw Damper Module | | | |
| B29006-1 | Simulator - Yaw Damper/Stabilizer Trim Module | | | |
| B30001-1 | Test equipment, Windshield Rain Repellent System | | Replaced by B30001-7 | |
| B30001-7 | Test equipment, Windshield Rain Repellent System | | | |
| B30002-1 | Cleaning Tank Assy, Windshield Rain Repellent Syst | | | |
| B32050-1 | Assembly Fixture, MLG | | Replaced by B32050-50 | |
| B32050-50 | Assembly Fixture, MLG | | | |
| B34001-1 | Test Fixture, Power Suply Cards/Control panel Assy | | | |
| B36005-2 | Plug Equipment, Duct Test | | Replaced by B36005-4 | |
| B36005-4 | Plug Equipment, Duct Test | | | |
| B49001-34 | Frame, APU Installation and Removal | | Replaced by B49001-35 | |
| B49001-35 | Frame, APU Installation and Removal | | | |
| B49002-1 | Stand, APU, Maintenance and Transportation | | Replaced by B49002-64 | |
| B49002-64 | Stand, APU, Maintenance and Transportation | | | |
| B49003-1 | Sling, APU Handling | | Replaced by B49003-10 | |
| B49003-10 | Sling, APU Handling | | | |
| B52004-1 | Installation Tool, Door Seal | | | |
| B54001-25 | Hydraulic Pump, Engine C Duct | | Replaced by B54001-30 | |
| B54001-30 | Hydraulic Pump, Engine C Duct | | | |
| B54016-1 | Removal Tool, Split Bushing | | | |
| B71034-13 | Test equipment, Engine Pressure Monitoring | | Replaced by B71034-48 | |
| B71034-29 | Test equipment, Engine Pressure Monitoring | | | |
| B71034-48 | Test equipment, Engine Pressure Monitoring | | | |
| B71040-20 | Sling Equipment, Inlet Cowl | | Replaced by B71040-36 | |
| B71040-21 | Sling Equipment, Inlet Cowl | | Replaced by B71040-37 | |
| B71040-23 | Sling Equipment, Inlet Cowl | | Replaced by B71040-39 | |
| B71040-36 | Sling Equipment, Inlet Cowl | | Replaced by B71040-39 | |
| B71040-37 | Sling Equipment, Inlet Cowl | | Replaced by B71040-39 | |
| B71040-39 | Sling Equipment, Inlet Cowl | | | |
| B71044-10 | Adapter Eqmnt, Load Test, Press Relief Door Latch | | Replaced by B71044-28 | |
| B71044-28 | Adapter Eqmnt, Load Test, Press Relief Door Latch | | | |
| B76003-1 | Rigging Equipment, Engine Control System | | | |
| B76004-1 | Adapter, Thurst Control Inner Shaft | | | |
| B78001-1 | Lock, Thrust Reverser Isolation Valve | | Replaced by B78001-14 | |
| B78001-14 | Lock, Thrust Reverser Isolation Valve | | | |
| B78001-2 | Lock, Thrust Reverser Isolation Valve | | | |
| B78001-5 | Lock, Thrust Reverser Isolation Valve | | | |
| BLS34529 | Assembly Bullet | | | AGE14279 |
| BLS34533 | Assembly Bullet | | | AGE14280 |
| C22005-1 | Breakout Box - Multipurpose, 100/124 Pin | | | |
| C22005-7 | Breakout Box - Multipurpose, 100/124 Pin | | | |
| C22005-8 | Breakout Box - Multipurpose, 100/124 Pin | | | |
| C23002-1 | Acoustic Coupler Equipment - XMTR and RCVR Assy | | | |
| C25001-1 | Wrench - Anti-Rattle Nut | | | |
| C25012-1 | Anti-Rattle Nut Wrench Kit | | | |
| C28013-6 | Protective Eqmnt, Ring, Lower Wing Pnl Access Door | | | |
| C34005-1 | Extender Box, Radio Altimeter Receiver Transmitter | | | |
| C34006-1 | Adapter, Tray, EFIS Symbol Generator Software Load | | Replaced by C34006-53 | |
| C34006-53 | Adapter, Tray, EFIS Symbol Generator Software Load | | Replaced by C34006-57 | |
| C34006-57 | Adapter, Tray, EFIS Symbol Generator Software Load | | | |
| C34012-2 | Test Box, Total Air Temp Probe, ADS | | | |
| C35003-1 | Retraction Equipment, Firing Pin, Oxygen System | | | |
| C38001-1 | Drain Mast Plug, Waste Water | | Replaced by C38001-23 | |
| C38001-23 | Drain Mast Plug, Waste Water | | | |
| C77004-1 | Test Box, Generic Airborne AVM Interface | | | |
| C77004-10 | Test Box, Generic Airborne AVM Interface | | | |
| C78005-17 | Hand Pump, Opening System, Thrust Reverser | | Replaced by C78005-21 | |
| C78005-21 | Hand Pump, Opening System, Thrust Reverser | | | |
| DAS34530 | Sizing Die | | | AGE14032 |
| DAS34534 | Sizing Die | | | AGE14033 |
| F70199-13 | Inflation Tool - Tire | | | |
| F70199-17 | Inflation Tool - Tire | | | |
| F70199-19 | Inflation Tool - Tire | | | |
| F70199-20 | Inflation Tool - Tire | | | |
| F70200-14 | Inflation Tool, Strut | | | |
| F70206-1 | Adapter Assembly, Fuel Leak Tracing Hollow Bolt | | | |
| F70230-1 | Repair Tool - Fuel System Self-Sealing Rivets | | | |
| F70258-1 | Personel Safety barrier, Main Deck Cargo Door | | | |
| F70284-1 | Wear Gage Set - Ground Power Plug and Receptacle | | | |
| F70300-1 | Adapter - Flap Drive | | | |
| F70312-25 | Crowfoot Wrench | | | |
| F70312-27 | Crowfoot Wrench | | | |
| F70312-28 | Crowfoot Wrench | | | |
| F70312-29 | Crowfoot Wrench | | | |
| F70312-30 | Crowfoot Wrench | | | |
| F70312-31 | Crowfoot Wrench | | | |
| F70312-32 | Crowfoot Wrench | | | |
| F70312-34 | Crowfoot Wrench | | | |
| F70312-35 | Crowfoot Wrench | | | |
| F70312-39 | Crowfoot Wrench | | | |
| F70312-40 | Crowfoot Wrench | | | |
| F70312-41 | Crowfoot Wrench | | | |
| F70312-42 | Crowfoot Wrench | | Replaced by F70312-52 | |
| F70312-45 | Crowfoot Wrench | | | |
| F70312-46 | Crowfoot Wrench | | | |
| F70312-47 | Crowfoot Wrench | | | |
| F70312-48 | Crowfoot Wrench | | | |
| F70312-49 | Crowfoot Wrench | | | |
| F70312-50 | Crowfoot Wrench | | | |
| F70312-52 | Crowfoot Wrench | | | |
| F70313-1 | Standard Box - Support Equipment | | | |
| F70313-2 | Standard Box - Support Equipment | | | |
| F70313-3 | Standard Box - Support Equipment | | | |
| F70313-4 | Standard Box - Support Equipment | | | |
| F70321-1 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-10 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-11 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-12 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-13 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-14 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-15 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-16 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-17 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-18 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-19 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-2 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-20 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-21 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-22 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-23 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-24 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-25 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-26 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-27 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-28 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-29 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-3 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-30 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-31 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-32 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-33 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-34 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-35 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-36 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-37 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-38 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-39 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-4 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-40 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-5 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-6 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-7 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-8 | Mandril - Shrink Fit Bushing Installation | | | |
| F70321-9 | Mandril - Shrink Fit Bushing Installation | | | |
| F70328-1 | Probe, Film Resistance Measuring | | | |
| F70330-4 | Static Balance Equipment, Control Surfaces | | | |
| F70330-87 | Static Balance Equipment, Control Surfaces | | | |
| F71329 | Leakage Tracing Device - Integral Tank Leakage Tst | | | |
| F72951-1 | Test Equipment, Water Manometer | | | |
| F72959-1 | Spanner Wrench - AN Standard Type | | | |
| F72959-10 | Spanner Wrench - AN Standard Type | | | |
| F72959-11 | Spanner Wrench - AN Standard Type | | | |
| F72959-12 | Spanner Wrench - AN Standard Type | | | |
| F72959-2 | Spanner Wrench - AN Standard Type | | | |
| F72959-3 | Spanner Wrench - AN Standard Type | | | |
| F72959-31 | Spanner Wrench - AN Standard Type | | | |
| F72959-32 | Spanner Wrench - AN Standard Type | | | |
| F72959-33 | Spanner Wrench - AN Standard Type | | | |
| F72959-34 | Spanner Wrench - AN Standard Type | | | |
| F72959-35 | Spanner Wrench - AN Standard Type | | | |
| F72959-36 | Spanner Wrench - AN Standard Type | | | |
| F72959-37 | Spanner Wrench - AN Standard Type | | | |
| F72959-38 | Spanner Wrench - AN Standard Type | | | |
| F72959-39 | Spanner Wrench - AN Standard Type | | | |
| F72959-4 | Spanner Wrench - AN Standard Type | | | |
| F72959-40 | Spanner Wrench - AN Standard Type | | | |
| F72959-41 | Spanner Wrench - AN Standard Type | | | |
| F72959-42 | Spanner Wrench - AN Standard Type | | | |
| F72959-5 | Spanner Wrench - AN Standard Type | | | |
| F72959-6 | Spanner Wrench - AN Standard Type | | Replaced by F72959-35 | |
| F72959-7 | Spanner Wrench - AN Standard Type | | | |
| F72959-8 | Spanner Wrench - AN Standard Type | | | |
| F72959-8 | Spanner Wrench - AN Standard Type | | Alternative of F72959-41 | |
| F72959-9 | Spanner Wrench - AN Standard Type | | | |
| F72977-62 | Gage Equipment, Hydr. Brake System Press Checking | | | |
| F80-0-50007 | Wrench, Special Torque | | | |
| F80085-1 | Test Fixture - Feel Actuator Cylinder Assembly | | | |
| F80113-105 | Kit - Roller Swage | | | |
| F80113-34 | Kit - Roller Swage | | Replaced by F80113-50 | |
| F80113-37 | Kit - Roller Swage | | | |
| F80113-44 | Kit - Roller Swage | | Replaced by F80113-61 | |
| F80113-50 | Kit - Roller Swage | | Replaced by F80113-105 | |
| F80113-50 | Kit - Roller Swage | | Replaced by F80113-64 | |
| F80113-61 | Kit - Roller Swage | | | |
| F80113-64 | Kit - Roller Swage | | Replaced by F80113-105 | |
| F80113-70 | Kit - Roller Swage | | Replaced by F80113-88 | |
| F80113-88 | Kit - Roller Swage | | | |
| F80212-1 | Adapter - Rudder Pedal Force Check | | Replaced by F80212-19 | |
| F80212-19 | Adapter - Rudder Pedal Force Check | | Replaced by F80212-30 | |
| F80212-30 | Adapter - Rudder Pedal Force Check | | | |
| G21007-1 | Air Flow Cup - Low/High Blow Test | | | |
| G22003-1 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-107 | |
| G22003-107 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-132 | |
| G22003-108 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-133 | |
| G22003-132 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-134 | |
| G22003-133 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-135 | |
| G22003-134 | Test Equipment - Autothrottle Clutch | | | |
| G22003-135 | Test Equipment - Autothrottle Clutch | | | |
| G22003-2 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-108 | |
| G22003-50 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-107 | |
| G22003-51 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-108 | |
| G22003-83 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-107 | |
| G22003-89 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-108 | |
| G22003-92 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-107 | |
| G22003-93 | Test Equipment - Autothrottle Clutch | | Replaced by G22003-108 | |
| G23001-32 | Test Box - Radio Communications Panel Procssr Card | | Replaced by G23001-37 | |
| G23001-37 | Test Box - Radio Communications Panel Procssr Card | | | |
| G23001-41 | Test Box - Radio Communications Panel Procssr Card | | | |
| G24005-1 | Dispatch Equipment - IDG, CF6-80C2 | | Replaced by G24005-24 | |
| G24005-24 | Dispatch Equipment - IDG, CF6-80C2 | | | |
| G24006-1 | Support Hook - Engine Power Feed Cable, PW4000 | | | |
| G24007-1 | Dispatch Kit - IDG, P&W engines | | Replaced by A24012-1 | |
| G24009-1 | IDG Dispatch Kit - RB211-524 | | | |
| G24011-1 | Hoist System - RB211, CF6-50 & JT9D Eng Accessory | | Replaced by A71015-107 | |
| G24013-1 | Accessory Adapter - Hoist System RB211 & CF6-50 | | | |
| G26004-1 | Extended Card - Electronic Card File | | Replaced by G26004-39 | |
| G26004-10 | Extended Card - Electronic Card File | | Replaced by G26004-39 | |
| G26004-23 | Extended Card - Electronic Card File | | Replaced by G26004-40 | |
| G26004-39 | Extended Card - Electronic Card File | | | |
| G26004-40 | Extended Card - Electronic Card File | | | |
| G26005-1 | Adapter - Hot Wire Anemometer | | Replaced by G26005-9 | |
| G26005-13 | Adapter - Hot Wire Anemometer | | Replaced by G26005-17 | |
| G26005-13 | Adapter - Hot Wire Anemometer | | Replaced by G26005-24 | |
| G26005-17 | Adapter - Hot Wire Anemometer | | Replaced by G26005-24 | |
| G26005-24 | Adapter - Hot Wire Anemometer | | | |
| G26005-9 | Adapter - Hot Wire Anemometer | | Replaced by G26005-24 | |
| G27033-2 | Adapter Cable - Outboard Aileron Lockout | | | |
| G28005-14 | Check Fixture Equipment, Pressure Relief Valve | | Replaced by G28005-42 | |
| G28005-18 | Check Fixture Equipment, Pressure Relief Valve | | Replaced by G28005-42 | |
| G28005-23 | Check Fixture Equipment, Pressure Relief Valve | | Replaced by G28005-42 | |
| G28005-29 | Check Fixture Equipment, Pressure Relief Valve | | Replaced by G28005-42 | |
| G28005-35 | Check Fixture Equipment, Pressure Relief Valve | | Replaced by G28005-42 | |
| G28005-42 | Check Fixture Equipment, Pressure Relief Valve | | | |
| G28018-1 | Test Equipment, Engine Fuel Feed Manifold | | Replaced by G28018-26 | |
| G28018-26 | Test Equipment, Engine Fuel Feed Manifold | | Replaced by G28018-28 | |
| G28018-28 | Test Equipment, Engine Fuel Feed Manifold | | | |
| G28018-29 | Test Equipment, Engine Fuel Feed Manifold | | | |
| G28018-3 | Test Equipment, Engine Fuel Feed Manifold | | Replaced by G28018-29 | |
| G28018-4 | Test Equipment, Engine Fuel Feed Manifold | | | |
| G28018-5 | Test Equipment, Engine Fuel Feed Manifold | | | |
| G28018-6 | Test Equipment, Engine Fuel Feed Manifold | | | |
| G32021-1 | Force Gage Equipment, Landing Gear Lever | | Replaced by G32021-18 | |
| G32021-18 | Force Gage Equipment, Landing Gear Lever | | | |
| G34004-11 | Adjustment Equipment, Wheather Radar Antenna Mount | | Replaced by G34004-17 | |
| G34004-17 | Adjustment Equipment, Wheather Radar Antenna Mount | | | |
| G35003-1 | Restraining Equipment, PSU, Oxygen Doors | | | |
| G36035-1 | Test Equipment, Pneumatic Health Check | | | |
| G36035-2 | Test Equipment, Pneumatic Health Check | | Replaced by G36035-2 | |
| G36035-36 | Test Equipment, Pneumatic Health Check | | | |
| G38004-10 | Blockage Removal Tool, Vaccum Lavatory System | | Replaced by G38004-13 | |
| G38004-13 | Blockage Removal Tool, Vaccum Lavatory System | | | |
| G38004-6 | Blockage Removal Tool, Vaccum Lavatory System | | Replaced by G38004-10 | |
| G38005-1 | Test Chamber Equipment, Lavatory Service Panel | | Replaced by G38005-111 | |
| G38005-111 | Test Chamber Equipment, Lavatory Service Panel | | | |
| G38005-61 | Test Chamber Equipment, Lavatory Service Panel | | | |
| G38006-1 | Blocakge Removal Equipment, Vacuum Waste System | | | |
| G51002-1 | Fall Protection, Overhead Personnel Support | | Replaced by G51003-1 | |
| G51003-1 | Fall Protection, Overhead Personnel Support | | | |
| G54007-165 | Strut Sling, Preload/Unload, Diagonal Brace | | | |
| G54007-80 | Strut Sling, Preload/Unload, Diagonal Brace | | Replaced by G54007-165 | |
| G54007-82 | Strut Sling, Preload/Unload, Diagonal Brace | | | |
| G54007-91 | Strut Sling, Preload/Unload, Diagonal Brace | | | |
| G54007-93 | Strut Sling, Preload/Unload, Diagonal Brace | | | |
| G71002-45 | Cradle, CF6-80C2B Engine | | Replaced by G71002-48 | |
| G71002-48 | Cradle, CF6-80C2B Engine | | | |
| G71007-16 | Sling Equipment, Inlet Cowl, CF6-80C2B Engine | | Replaced by G71007-28 | |
| G71007-28 | Sling Equipment, Inlet Cowl, CF6-80C2B Engine | | | |
| G71008-1 | Proof Load Equipment, Cradle, CF6-80C2B Engine | | | |
| G71010-67 | Sling, Engine Handling, GE Engines | | Replaced by G71010-79 | |
| G71010-68 | Sling, Engine Handling, GE Engines | | Replaced by G71010-80 | |
| G71010-69 | Sling, Engine Handling, GE Engines | | Replaced by G71010-81 | |
| G71010-79 | Sling, Engine Handling, GE Engines | | | |
| G71010-80 | Sling, Engine Handling, GE Engines | | | |
| G71010-81 | Sling, Engine Handling, GE Engines | | | |
| G71012-107 | Locating Jig, Engine Build-up to Strut, CF6-80C2B | | | |
| G71012-118 | Locating Jig, Engine Build-up to Strut, CF6-80C2B | | | |
| G71012-119 | Locating Jig, Engine Build-up to Strut, CF6-80C2B | | | |
| G71012-3 | Locating Jig, Engine Build-up to Strut, CF6-80C2B | | Replaced by G71012-118 | |
| G71012-4 | Locating Jig, Engine Build-up to Strut, CF6-80C2B | | Replaced by G71012-119 | |
| G71013-1 | Sling, Fan Cowl, CF6-80C2B | | | |
| G71014-1 | Beam, Engine Hanling, RB211-524 | | | |
| G71015-1 | Cradle, RB211-524 (G & H) Engine | | Replaced by G71015-75 | |
| G71015-75 | Cradle, RB211-524 (G & H) Engine | | | |
| G71017-1 | Proof Load Fixture, RB211-524 | | | |
| G71018-1 | Support Equipment, RB211-524, H2 Handling Attachmt | | | |
| G71020-1 | Wrench, Flex Nut, 15th Stage, Manfld & Dct, PW4000 | | | |
| G71021-1 | Drive extension - Starter Vale and PRSOV | | Replaced by G71021-16 | |
| G71021-11 | Drive extension - Starter Vale and PRSOV | | Replaced by G71021-16 | |
| G71021-16 | Drive extension - Starter Vale and PRSOV | | | |
| G71021-6 | Drive extension - Starter Vale and PRSOV | | Replaced by G71021-16 | |
| G71022-1 | Hold Open Eqmnt, Engine Fan/Core Cowl, CF6-80C2B | | Replaced by G71022-44 | |
| G71022-44 | Hold Open Eqmnt, Engine Fan/Core Cowl, CF6-80C2B | | | |
| G71023-1 | Hold Open Equipment, PW4000 Fan and Core Cowls | | Replaced by G71023-52 | |
| G71023-52 | Hold Open Equipment, PW4000 Fan and Core Cowls | | | |
| G71030-1 | Sling Equipment, Nose Cowl, RB211-524 & CF6-50 | | | |
| G71032-1 | Sling Equipment, Inlet Cowl, CF6-50 & RB211-524 | | Replaced by G71030-1 | |
| G76002-15 | Protractor, Thrust Reverser Lever, Fwd & Reverse | | | |
| G76002-7 | Protractor, Thrust Reverser Lever, Fwd & Reverse | | Replaced by G76002-15 | |
| G78002-1 | Hold Open Set, Thrust Reverser Cowl, CF6-80C2B | | | |
| G78003-1 | Sling Equipment, Fan Reverser, CF6-80C2B | | Replaced by G78003-53 | |
| G78003-53 | Sling Equipment, Fan Reverser, CF6-80C2B | | | |
| G78005-1 | Adapter Equipment, Thrust Reverser Hold Open Rod | | Replaced by G78005-10 | |
| G78005-10 | Adapter Equipment, Thrust Reverser Hold Open Rod | | | |
| G78006-1 | Dolly, Thrust Reverser, CF6-80C2 | | Replaced by G78006-74 | |
| G78006-2 | Dolly, Thrust Reverser, CF6-80C2 | | Replaced by G78006-75 | |
| G78006-74 | Dolly, Thrust Reverser, CF6-80C2 | | | |
| G78006-75 | Dolly, Thrust Reverser, CF6-80C2 | | | |
| J07008-1 | Sling - Tethering/Lifting Airplane Recovery | | Replaced by J07008-22 | |
| J07008-22 | Sling - Tethering/Lifting Airplane Recovery | | Replaced by J07008-30 | |
| J07008-30 | Sling - Tethering/Lifting Airplane Recovery | | | |
| J20002-1 | Load Positioner - Engine Accessories, 250 lb cap | | Replaced by J20002-36 | |
| J20002-36 | Load Positioner - Engine Accessories, 250 lb cap | | | |
| J20009-38 | Jacking Equipment, Hydraulic Telescoping | | Replaced by J20009-78 | |
| J20009-70 | Jacking Equipment, Hydraulic Telescoping | | | |
| J20009-78 | Jacking Equipment, Hydraulic Telescoping | | | |
| J22004-1 | Test Equipment - Autothrottle, Gearbox, Brake | | Replaced by J22004-67 | |
| J22004-2 | Test Equipment - Autothrottle, Gearbox, Brake | | Replaced by J22004-68 | |
| J22004-54 | Test Equipment - Autothrottle, Gearbox, Brake | | Replaced by J22004-67 | |
| J22004-55 | Test Equipment - Autothrottle, Gearbox, Brake | | Replaced by J22004-68 | |
| J22004-67 | Test Equipment - Autothrottle, Gearbox, Brake | | | |
| J22004-68 | Test Equipment - Autothrottle, Gearbox, Brake | | | |
| J23001-1 | Hoist Adapter - SATCOM top,Mounted H. Gain Antenna | | Replaced by J23001-12 | |
| J23001-12 | Hoist Adapter - SATCOM top,Mounted H. Gain Antenna | | | |
| J24002-73 | Hoist Adapter Assembly - IDG | | Replaced by A24011-1 | |
| J24015-1 | Pressure Test Equipment - Engine Generators | | | |
| J25001-1 | Lever - Stowage Bin Release | | Replaced by J25001-5 | |
| J25001-5 | Lever - Stowage Bin Release | | | |
| J25003-25 | Test Equipment - Lateral Guide Assembly | | | |
| J26005-24 | Test Equipment - Fire Extinguisher Tubing, Cargo B | | Replaced by J26005-32 | |
| J26005-24 | Test Equipment - Fire Extinguisher Tubing, Cargo B | | Replaced by J26009-1 | |
| J26005-32 | Test Equipment - Fire Extinguisher Tubing, Cargo B | | Replaced by J26009-1 | |
| J26007-1 | Test Box - Cargo Smoke Heater, Test Plug | | | |
| J26009-1 | Test Equipment - Fire Extinguisher Tubing, Cargo B | | | |
| J27054-1 | Test Equipment - Leakage Test | | | |
| J27079-31 | Inspection Equipment - Elevator Freeplay | | | |
| J28006-1 | Sealing Tool, Rivet, Fuel tank | | | |
| J28007-1 | Pressurization Eqt, Wing Dry Bay, Fuel Leak Detect | | Replaced by J28007-10 | |
| J28007-1 | Pressurization Eqt, Wing Dry Bay, Fuel Leak Detect | | Replaced by J28007-9 | |
| J28007-10 | Pressurization Eqt, Wing Dry Bay, Fuel Leak Detect | | | |
| J28007-9 | Pressurization Eqt, Wing Dry Bay, Fuel Leak Detect | | | |
| J28010-1 | Console, Shop Air Supply | | Replaced by J28010-26 | |
| J28010-26 | Console, Shop Air Supply | | | |
| J28013-1 | Fitting Equipment, Fuel Drain Sump | | | |
| J29005-30 | Plug Set, Pressure Test, Hydraulic Reservoir Assy | | | |
| J32001-43 | Measuring Equipment, Brake Pedal | | Replaced by J32001-63 | |
| J32001-46 | Measuring Equipment, Brake Pedal | | Replaced by J32001-64 | |
| J32001-63 | Measuring Equipment, Brake Pedal | | Replaced by J32001-64 | |
| J32001-64 | Measuring Equipment, Brake Pedal | | | |
| J32010-58 | Puller Equipment, Wheel and Brake Sleeve, MLG Axle | | | |
| J32010-62 | Puller Equipment, Wheel and Brake Sleeve, MLG Axle | | | |
| J32012-1 | Puller Equipment, Brake, MLG | | Replaced by J32012-18 | |
| J32012-18 | Puller Equipment, Brake, MLG | | | |
| J32031-1 | Protector Equipment, Axle, MLG | | | |
| J32031-12 | Protector Equipment, Axle, MLG | | | |
| J32032-1 | Wrench equipment, Wheel Retention Nut, MLG | | Replaced by J32031-12 | |
| J32032-1 | Wrench equipment, Wheel Retention Nut, MLG | | Replaced by J32032-22 | |
| J32032-19 | Wrench equipment, Wheel Retention Nut, MLG | | Replaced by J32032-22 | |
| J32032-22 | Wrench equipment, Wheel Retention Nut, MLG | | | |
| J32057-1 | Fixture Equipment, Landing Gear Actuator Assembly | | Replaced by J32057-108 | |
| J32057-108 | Fixture Equipment, Landing Gear Actuator Assembly | | | |
| J32057-94 | Fixture Equipment, Landing Gear Actuator Assembly | | Replaced by J32057-108 | |
| J32060-1 | Drain Equipment, Oleo Strut, MLG/NLG | | | |
| J32065-1 | Alignment Pin, MLG Tow Fitting | | | |
| J34002-1 | Test Fixture, Angle of Attack | | Replaced by J34002-18 | |
| J34002-18 | Test Fixture, Angle of Attack | | Replaced by J34002-19 | |
| J34002-19 | Test Fixture, Angle of Attack | | | |
| J38001-1 | Pressurization Equipment, Waste Drain System | | Replaced by J38001-16 | |
| J38001-16 | Pressurization Equipment, Waste Drain System | | | |
| J51003-1 | Static Balance Equipment, Flight Control Surfaces | | | |
| J52024-2 | Test equipment, Latch Assembly, Blow Out Doors | | | |
| J54001-73 | Strut Unload Sling, Diagonal Brace Alignment | | | |
| J54001-74 | Strut Unload Sling, Diagonal Brace Alignment | | | |
| J54001-75 | Strut Unload Sling, Diagonal Brace Alignment | | | |
| J54001-76 | Strut Unload Sling, Diagonal Brace Alignment | | | |
| J71006 | Powered Hoist System, GSE Operations | | | |
| J76002-1 | Wrench, Spanner, Thrust Lever Cntrl Stnd Shft Assy | | | |
| ME65B40136-1 | Mechanical Equipment - Pitot Static Probe | | Replaced by A10002-9 | |
| ME65B83635 | Torque Wrench Adapter, Brakes, Side cargo Door | | | |
| MIT114T3000 | Spacer Kit - Inbd/Outb Slat Installation | | | |
| MIT65B01202-1 | Adapter Assembly Wrench, Landing gear Wheel Retain | | Replaced by J32032-22 | |
| MIT65B92408-1 | Alignment Fixture - Adapter Shaft | | | |
| N7575-6-48 | Crowfoot Wrench | | Replaced by F70312-25 | |
| PL1 | Pinglite | | | |
| PME65B89603 | Hoist System - RB211, CF6-50 & JT9D Eng Accessory | | Replaced by G24011-1 | |
| PWA25056 | Equipment, Engine Support | | | |
| PWA25757 | Equipment, Engine Support | | | |
| PWA25758 | Equipment, Engine Support | | | |
| PWA29245 | Equipment, Engine Support | | | |
| SE24-4001 | Wear Gage Set - Ground Power Plug and Receptacle | | Replaced by F70284-1 | |
| ST1065C | Installation Set - NAS1368 Grommet | | Replaced by A20006-32 | |
| ST1864P | Reamer - Carbide Straight Flute | | | |
| ST2580-163A | Wrench, Spanner Type | | Replaced by ST2580-334C-1-185 | |
| ST2580-302 | Wrench, Spanner | | | |
| ST2580-334C-1-145 | Standard Tool - Spanner Nose Pliers | | | |
| ST2580-334C-1-185 | Standard Tool - Spanner Nose Pliers | | | |
| ST2580-381 | Wrench, Spanner, Face Type | | | |
| ST2583-1 | Adapter - Flap Drive | | Replaced by F70300-1 | |
| ST2590-245 | Crowfoot Wrench | | Replaced by F70312-25 | |
| ST848-1000 | Installation Tool, O-ring | | | |
| ST848-1250 | Installation Tool, O-ring | | | |
| ST848-1500 | Installation Tool, O-ring | | | |
| ST848-1750 | Installation Tool, O-ring | | | |
| ST848-187 | Installation Tool, O-ring | | | |
| ST848-250 | Installation Tool, O-ring | | | |
| ST848-312 | Installation Tool, O-ring | | | |
| ST848-375 | Installation Tool, O-ring | | | |
| ST848-500 | Installation Tool, O-ring | | | |
| ST848-625 | Installation Tool, O-ring | | | |
| ST848-750 | Installation Tool, O-ring | | | |
| ST848R | Removal Tool - O-ring | | | |
| ST8709H | Go/No Go Gage, Assembly Wiggens BACC24R Coupling | | | |
| ST878D | Sleev-Set Tool - Flareless Tube Fitting | | | |
| ST878D-10-028 | BACS13AP Installation Tool | | | |
| ST878D-10-035 | BACS13AP Installation Tool | | | |
| ST878D-10-049 | BACS13AP Installation Tool | | | |
| ST878D-10-058 | BACS13AP Installation Tool | | | |
| ST878D-10-083 | BACS13AP Installation Tool | | | |
| ST878D-12-020 | BACS13AP Installation Tool | | | |
| ST878D-12-028 | BACS13AP Installation Tool | | | |
| ST878D-12-035 | BACS13AP Installation Tool | | | |
| ST878D-12-042 | BACS13AP Installation Tool | | | |
| ST878D-12-049 | BACS13AP Installation Tool | | | |
| ST878D-12-058 | BACS13AP Installation Tool | | | |
| ST878D-3-020 | BACS13AP Installation Tool | | | |
| ST878D-3-028 | BACS13AP Installation Tool | | | |
| ST878D-3-035 | BACS13AP Installation Tool | | | |
| ST878D-4-020 | BACS13AP Installation Tool | | | |
| ST878D-4-028 | BACS13AP Installation Tool | | | |
| ST878D-4-035 | BACS13AP Installation Tool | | | |
| ST878D-5-020 | BACS13AP Installation Tool | | | |
| ST878D-5-028 | BACS13AP Installation Tool | | | |
| ST878D-5-035 | BACS13AP Installation Tool | | | |
| ST878D-6-020 | BACS13AP Installation Tool | | | |
| ST878D-6-028 | BACS13AP Installation Tool | | | |
| ST878D-6-035 | BACS13AP Installation Tool | | | |
| ST878D-8-028 | BACS13AP Installation Tool | | | |
| ST878D-8-035 | BACS13AP Installation Tool | | | |
| ST878D-8-049 | BACS13AP Installation Tool | | | |
| ST879A | Tube Presetting Tool - Flareless | | | |
| ST879AF | Holding Fixture - Hand Preset Tools | | | |
| ST918C | Mandrel - Roller Bearing Pressing | | | |
| ST919 | Support - Bearing Installation | | | |
| ST919-MP | Mounting Plate | | | |
| ST926E-104 | Roller Swaging Tool - Bearing | | | |
| ST926E-111 | Roller Swaging Tool - Bearing | | | |
| ST926E-130 | Roller Swaging Tool - Bearing | | | |
| ST926E-136 | Roller Swaging Tool - Bearing | | | |
| ST926E-162 | Roller Swaging Tool - Bearing | | | |
| ST926E-169 | Roller Swaging Tool - Bearing | | | |
| ST926E-172 | Roller Swaging Tool - Bearing | | | |
| ST926E-175 | Roller Swaging Tool - Bearing | | | |
| ST926E-53 | Roller Swaging Tool - Bearing | | | |
| ST926E-63 | Roller Swaging Tool - Bearing | | | |
| ST926E-70 | Roller Swaging Tool - Bearing | | | |
| ST926E-77 | Roller Swaging Tool - Bearing | | | |
| ST926E-84 | Roller Swaging Tool - Bearing | | | |
| ST926E-90 | Roller Swaging Tool - Bearing | | | |
| ST926E-97 | Roller Swaging Tool - Bearing | | | |
| ST927 | Removal Tool - Bearing | | | |
| ST927C-1 | Bearing Removal Tool | | | |
| ST927C-10 | Bearing Removal Tool | | | |
| ST927C-108 | Bearing Removal Tool | | | |
| ST927C-11 | Bearing Removal Tool | | | |
| ST927C-112 | Bearing Removal Tool | | | |
| ST927C-113 | Bearing Removal Tool | | | |
| ST927C-114 | Bearing Removal Tool | | | |
| ST927C-12 | Bearing Removal Tool | | | |
| ST927C-121 | Bearing Removal Tool | | | |
| ST927C-125 | Bearing Removal Tool | | | |
| ST927C-127 | Bearing Removal Tool | | | |
| ST927C-13 | Bearing Removal Tool | | | |
| ST927C-131 | Bearing Removal Tool | | | |
| ST927C-134 | Bearing Removal Tool | | | |
| ST927C-136 | Bearing Removal Tool | | | |
| ST927C-137 | Bearing Removal Tool | | | |
| ST927C-139 | Bearing Removal Tool | | | |
| ST927C-14 | Bearing Removal Tool | | | |
| ST927C-142 | Bearing Removal Tool | | | |
| ST927C-145 | Bearing Removal Tool | | | |
| ST927C-15 | Bearing Removal Tool | | | |
| ST927C-16 | Bearing Removal Tool | | | |
| ST927C-17 | Bearing Removal Tool | | | |
| ST927C-18 | Bearing Removal Tool | | | |
| ST927C-19 | Bearing Removal Tool | | | |
| ST927C-2 | Bearing Removal Tool | | | |
| ST927C-20 | Bearing Removal Tool | | | |
| ST927C-21 | Bearing Removal Tool | | | |
| ST927C-22 | Bearing Removal Tool | | | |
| ST927C-23 | Bearing Removal Tool | | | |
| ST927C-3 | Bearing Removal Tool | | | |
| ST927C-4 | Bearing Removal Tool | | | |
| ST927C-5 | Bearing Removal Tool | | | |
| ST927C-6 | Bearing Removal Tool | | | |
| ST927C-7 | Bearing Removal Tool | | | |
| ST927C-8 | Bearing Removal Tool | | | |
| ST927C-80 | Bearing Removal Tool | | | |
| ST927C-81 | Bearing Removal Tool | | | |
| ST927C-82 | Bearing Removal Tool | | | |
| ST927C-83 | Bearing Removal Tool | | | |
| ST927C-84 | Bearing Removal Tool | | | |
| ST927C-85 | Bearing Removal Tool | | | |
| ST927C-86 | Bearing Removal Tool | | | |
| ST927C-9 | Bearing Removal Tool | | | |
| ST929-2C | Staking Tool - Bearing Sleeve, Six Point | | | |
| ST932 | Roller Staking Tool | | | |
| ST991A-2 | Removal Tool - Scrivet Fastener | | | |
| WAS33662 | Wrench, RAT Hub Bearing Installation/Removal | | | AGE14727 |